LSAT - ≥99.9% metals basis, single crystal substrate, <100>

Cat. No.: L476258
AVAILABLE TO ORDER
GRADE & PURITY ≥99.9% metals basis single crystal substrate, <100>
Synonyms
Lanthanum aluminum oxide-strontium aluminum tantalum oxide
Storage
Room temperature
★
Size
Germany (EU)
USA*
Price
Qty
1EA
L476258-1EA
Made to order · 8–12 wks

€550.06

€642.04
Save €91.98 (14.33%)
Enter a quantity for the sizes you want to add.

Specifications

Synonyms
Lanthanum aluminum oxide-strontium aluminum tantalum oxide
Specifications & Purity
≥99.9% metals basis, single crystal substrate, <100>
Storage
Room temperature
Purity
≥99.9% metals basis

Advanced Data

Certificates (CoA,COO,BSE/TSE and Analysis Chart)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:
Solution Calculators
Reviews

Customer Reviews

Application Protocols

No assay protocols (e.g., WB, IHC, IF, FC) apply to this materials-science substrate. For process use, general, non-item-specific workflow examples include:

  • Epitaxial thin-film deposition (PLD):
    1. Handle in clean environment; blow off particles with filtered N2.
    2. Sequential solvent clean (acetone, IPA), dry.
    3. Optional UV-ozone or O2 plasma clean.
    4. Load into chamber; heat to growth temperature under O2 background; grow film; cool in O2 to avoid oxygen vacancies.
  • AFM/XRD characterization:
    1. Inspect surface with AFM (tapping mode) for step-terrace morphology.
    2. Verify orientation and mosaic via HRXRD/rocking curves or in-situ RHEED.
  • Device patterning (general):
    1. Apply photoresist; soft-bake per datasheet.
    2. Pattern and etch deposited film (substrate is typically etch-resistant but can be attacked by aggressive chemistries like HF).
    3. Deposit electrodes; lift-off. These are literature-style examples and not product-validated protocols. Adjust to your cleanroom standards and toolsets.
Biological Roles

This product is an inorganic crystalline oxide substrate intended for materials research. It does not have intrinsic biological roles or metabolic functions. Any interactions with biological systems would be incidental (e.g., as an inert support for biosensors or cell adhesion studies) and are highly protocol-dependent.

  • General/literature context:
    • Oxide substrates are sometimes used as inert, optically transparent supports for thin-film electrodes, biosensor coatings, or patterned functional materials. In such cases, biological effects derive from the deposited film or surface functionalization rather than the LSAT bulk.
    • Surface chemistry (hydroxylation state, roughness) may influence protein adsorption or cell adhesion, but LSAT is not a standardized bio-interface material; silanization or other functionalization would be required for reproducible bioassays.

No medical, diagnostic, or therapeutic use is intended or implied. For any bio-related application, validate biocompatibility and sterilization method experimentally and consult institutional biosafety guidance.

Buffer Applications

Not typically applicable. LSAT is an insoluble ceramic substrate and is not used to prepare buffer solutions or as a buffering agent. If LSAT substrates are used in experiments involving aqueous buffers (e.g., as a support for thin films in electrochemistry), select buffer systems based on the requirements of the film/electrode and verify that the buffer does not attack the oxide surface under your conditions.

Green Alternatives

Although “green chemistry” typically targets molecular reagents and solvents, substrate selection also affects environmental footprint through processing temperature, chemical consumption, and yield. The following comparison is general/literature-based and not item-specific.

  • Context: LSAT is a lead-free, refractory oxide substrate with good lattice match to many perovskite films, often enabling lower defect densities and fewer reprocess cycles.

  • Comparison (general):

    • LSAT vs SrTiO3 (STO): LSAT offers slightly smaller lattice parameter, sometimes reducing dislocation densities for compressively strained films; both are lead-free. STO can be photoactive and may reduce under vacuum; LSAT is typically more chemically robust in some etchants.
    • LSAT vs LaAlO3 (LAO): LAO can suffer from twinning and has a smaller lattice, imposing higher compressive strain; LSAT’s intermediate lattice can reduce need for thick buffer layers, cutting material and energy use.
    • LSAT vs MgO/Al2O3 (sapphire): Large lattice mismatch to perovskites often necessitates high-temperature buffers, increasing energy and chemical use. LSAT can enable direct growth.
    • LSAT vs Pb-containing substrates (e.g., PMN-PT actuators): LSAT avoids lead, reducing toxic metals in the workflow.

Tradeoffs: LSAT single crystals require energy-intensive growth; wafer reuse and careful process window optimization (fewer failed runs) are practical “green” levers. Surface treatments should minimize HF use; consider O2 plasma/UV-ozone where feasible.

Pharmaceutical Uses

Not applicable as a pharmaceutic. LSAT is an inorganic substrate for materials research and device fabrication, not an excipient or processing aid. It is not covered by pharmacopeial monographs. If used indirectly in analytical workflows (e.g., as a support in spectroscopy), such use remains research-only and outside of pharmaceutical formulation contexts. Research Use Note: For research use only.

Physical Properties
  • Item-specific numeric specifications (density, lattice parameter, dimensions, resistivity, optical constants): Not specified for this item; refer to CoA/Spec Sheet.
  • General/literature values for LSAT perovskite substrates (non-item-specific):
    • Phase: Inorganic oxide; typically single-crystal perovskite (ABO3) solid solution.
    • Appearance: Usually colorless to pale substrate/wafers or white ceramic (literature); actual item appearance not specified.
    • Crystal structure: Cubic perovskite at ambient conditions (literature), with reported pseudocubic lattice parameter around ~3.868–3.876 Å depending on exact composition and temperature.
    • Density: Literature reports in the ~6.5–6.8 g/cm3 range for bulk LSAT ceramics/single crystals.
    • Melting/decomposition: High-melting, refractory oxide; literature indicates stability well above 1800 °C (exact melting behavior depends on composition and peritectic equilibria).
    • Thermal expansion: Typical linear CTE values reported around 7–9 × 10^-6 K^-1 (room temperature to several hundred °C) in literature.
    • Dielectric properties: Relative permittivity often cited ~20–25 at 1 MHz, low dielectric loss (tan δ ≪ 0.01) at room temperature (literature, composition- and frequency-dependent).
    • Optical: Wide-bandgap insulating oxide; transparent in visible with refractive index typically ~2.0–2.1 at 632.8 nm (literature; varies with stoichiometry and wavelength).
    • Solubility: Insoluble in water and common organic solvents; subject to slow attack by hot concentrated acids/bases; HF can aggressively etch oxides (literature). Notes: Values above are provided for general context only and are not product specifications.
Quality and Grades
  • Item-specific grade/purity and substrate specifications: Not specified for this item; refer to CoA/Spec Sheet.
  • For LSAT in materials science, quality is typically defined by (general/literature):
    • Crystal quality: XRD rocking curve FWHM, dislocation density, twin density, and mosaic spread. High-quality epi-ready wafers exhibit low mosaicity and tight orientation tolerance (e.g., <0.1°) — item-specific values should be verified on the CoA.
    • Orientation and finish: Common orientations (001)/(110)/(111); single- or double-side polish; Ra surface roughness at the sub-nm level for epi-ready surfaces. Miscut angle and direction may be specified for step-flow growth control.
    • Size/flatness: Diameter/side length, thickness, TTV, LTV, bow/warp, and primary/secondary flat per SEMI standards (for round wafers) or edge bevels for square substrates.
    • Surface chemistry: As-received termination (e.g., A-site vs B-site enriched) is sometimes controlled by anneal/etch protocols; if critical, verify termination or perform pre-growth conditioning.
    • Cleanliness: Particle count and organic residue levels impact nucleation density; vendors may ship in cleanroom packaging to preserve surface quality.
  • Stabilizers/additives: Not applicable for single-crystal oxide substrates. If dopants or conductive variants are offered (e.g., Nb-doped perovskites), such features would be explicitly stated; none are specified here.
  • Documentation: Request XRD/Laue data, AFM roughness, and orientation certifications as needed for your process window.
Reaction and Applications
  • Manufacturer Applications: Not provided in the Product Data.
  • General/literature applications for LSAT substrates in materials science (non-item-specific):
    • Epitaxial growth platform for complex oxides (PLD, MBE, sputtering, CVD), including high-Tc cuprates, manganites (e.g., LSMO), ferroelectrics (e.g., BFO, PTO), multiferroics, and wide-bandgap perovskites.
    • Lattice engineering: Pseudocubic lattice parameter of LSAT provides intermediate mismatch between SrTiO3 (~3.905 Å) and LaAlO3 (~3.79 Å), enabling strain tuning of films to achieve targeted electronic/ferroelectric phases.
    • Dielectric/insulating substrate: Electrically insulating and low-loss, enabling microwave device structures and capacitor stacks without parasitic conduction.
    • Thermal robustness: Stable to high-temperature oxidizing environments used during oxide deposition and post-anneals.
    • Optical transparency: Visible transparency supports optical characterization (transmission, ellipsometry) and photonics research.
  • Practical tips (literature):
    • Pre-growth conditioning (anneal in O2 at 900–1100 °C) can improve terrace formation and reduce adsorbates; optimize for your orientation.
    • Surface termination control may affect film nucleation and step-flow; verify via AFM and XPS/TOF-SIMS where applicable.
    • Handle wafers with vacuum wands or edge grips to minimize contamination; store in clean polypropylene cassettes. Note: The exact suitability depends on orientation, miscut, and crystal quality — parameters not provided for this item.
Reaction Conditions

There are no “reaction conditions” in the classical solution-phase sense. However, for thin-film growth and surface conditioning on LSAT, literature provides typical, non-item-specific process envelopes (always optimize for your tool and film):

  • PLD growth of perovskite oxides:
    • Substrate temperature: ~650–800 °C (some systems up to ~900 °C).
    • Oxygen partial pressure: ~10^-4 to 0.5 Torr depending on film oxygenation needs; post-anneal in 0.2–1 atm O2 may improve stoichiometry.
    • Laser fluence/rep rate: film-dependent; substrate choice (LSAT) tolerates standard PLD ranges.
  • Oxide MBE:
    • Substrate temperature: ~600–800 °C; ozone or RF-activated oxygen provides reactivity at lower pressures (10^-8–10^-5 Torr O2-equivalent).
    • Termination: Pre-anneal in O2 can help terrace definition; confirm with RHEED/AFM.
  • Sputtering/CSD:
    • RF sputtering in Ar/O2 mixtures at modest substrate temperatures (500–750 °C) can yield epitaxy for compatible systems.
  • Surface preparation (example guidance):
    • Solvent clean (acetone/IPA), UV-ozone 10–30 min, then O2 anneal (e.g., 950–1050 °C, 1–4 h) to obtain step-terrace morphology. If using any acid/base etch, validate impact on termination and roughness. These ranges are literature guidelines for LSAT substrates and are not specifications for this item.
Safety and Handling
  • GHS classification, pictograms, hazard statements for this specific item: Not specified for this item; refer to SDS.
  • General safety considerations for ceramic perovskite oxides (literature/general):
    • Likely non-volatile, inert solid. Primary hazard is mechanical (sharp wafer edges) and nuisance dust if cutting, grinding, or polishing. Avoid inhalation of fine particulates—use local exhaust/HEPA capture when machining.
    • PPE: Safety glasses or face shield when handling wafers; cut-resistant gloves to prevent edge cuts; lab coat. If generating dust, add N95/FFP2 (or better) respiratory protection per institutional policy.
    • Incompatibilities: Avoid exposure to HF and strong fluoride-containing chemistries without appropriate materials controls (HF will etch and can generate severe dermal/systemic hazards). Hot concentrated alkali or acid may attack the surface and alter substrate quality.
    • First aid (overview; defer to SDS): If dust is inhaled, move to fresh air; seek medical attention if symptoms persist. For eye contact with particulates, rinse cautiously with water for several minutes and remove contact lenses if easy. For cuts from wafer edges, control bleeding and clean thoroughly.
    • Thermal handling: Substrates used in high-temperature processes should be cooled gradually to mitigate thermal shock and microcracking. Use appropriate tongs and heat-resistant PPE. Always consult the product-specific SDS for authoritative hazard, exposure limits, and emergency procedures.
Solvent Selection

This product is an inorganic solid substrate/ceramic, not a molecular solute; classic “solvent selection” for dissolution is not applicable. However, solvent choice does matter for cleaning and surface preparation (general/literature guidance):

  • Typical cleaning solvents for particulates/organics:
    • Acetone, isopropanol (IPA), and ultrapure water in sequential ultrasonic baths; dry with filtered N2. Avoid prolonged sonication that may induce edge chipping.
    • For more stringent organic removal, use semiconductor-grade solvents and fresh baths to minimize residue redeposition.
  • Oxide-compatible wet cleans (use with caution; literature):
    • Piranha (H2SO4/H2O2) or SC-1/SC-2 (RCA cleans) can remove organics/metallics but may alter surface termination and roughness; temperature/time must be controlled. Never mix with solvents; follow strict safety protocols.
    • HF-based dips are sometimes used to tailor termination on certain perovskites; HF is highly hazardous and can etch LSAT — apply only if your process requires it and with full safety controls.
  • Dry processes:
    • O2 plasma or UV-ozone for mild organic removal; excessive plasma exposure can modify near-surface stoichiometry.
  • When to choose LSAT vs other substrates (see Green Alternatives): consider lattice parameter, dielectric constant, and thermal expansion compatibility with the film material, not solvent effects. Always validate any wet clean on sacrificial pieces and measure AFM roughness/termination before device growth.
Storage and Reconstitution
  • Storage conditions (from Product Data): Room temperature.
  • Shipping: Not specified for this item; refer to CoA/Spec Sheet.
  • Reconstitution: Not applicable; solid substrate/ceramic requires no reconstitution.
  • General handling/storage guidance (materials-science practice):
    • Keep in original cleanroom-grade packaging until use. Store in a dry, dust-free environment; avoid contact with silicone-based materials that can transfer films.
    • Handle with powder-free gloves or finger cots to prevent organic contamination; use vacuum wands or edge grips to avoid fingerprints and edge chipping.
    • Protect surfaces from abrasion; use wafer cassettes or individual substrate boxes. Avoid stacking bare substrates.
    • If long-term storage is anticipated, consider desiccated cabinets to limit adsorption of moisture/contaminants. Record lot/orientation labels to maintain traceability.
    • Before critical depositions, perform a standard surface clean (e.g., solvent rinse and UV-ozone) to remove adventitious carbon picked up during storage. Refer to the product’s SDS and CoA for any additional item-specific storage notes or packaging details.
Structure and Identity
  • Item-specific identifiers (CAS, InChIKey, SMILES, Molecular Formula, Molecular Weight): Not specified for this item; refer to CoA/Spec Sheet.
  • Common materials-science name: LSAT (literature), widely used shorthand for a complex perovskite oxide solid solution.
  • Structural description (literature/general knowledge):
    • LSAT typically denotes a perovskite-type oxide derived from a solid solution between LaAlO3 and Sr(Al,Ta)O3 (often represented as (LaAlO3)0.3(Sr2AlTaO6)0.7 or, equivalently, (La,Sr)(Al,Ta)O3 with tailored cation ratios).
    • Crystal system: typically cubic perovskite at room temperature (literature), ABO3 motif with mixed A-site (La3+/Sr2+) and mixed B-site (Al3+/Ta5+) cations, charge-balanced by oxygen.
    • Key functional motifs: corner-sharing BO6 octahedra; A-site cations occupy 12-coordinate cuboctahedral sites, imparting a tunable lattice parameter and dielectric response.
    • Microstructure form in commerce: single-crystal wafers, substrates, or polycrystalline ceramics (literature). 2D depiction would show a cubic lattice with alternating A-site cations at cube corners, B-site at body center, O at face centers.
  • Stereochemistry: Not applicable; crystalline inorganic oxide with long-range order rather than discrete molecular stereocenters.
  • Notes: The exact composition, dopant level (if any), surface termination, orientation (e.g., (001), (110), (111)), and finish (single- vs double-side polish) are item-specific and not provided here; consult the product’s CoA/specification for definitive identity and crystallographic parameters.
Synthetic Utility

As a solid-state substrate rather than a molecular reagent, LSAT’s “synthetic utility” lies in templating and enabling thin-film synthesis (general/literature):

  • Epitaxial templating: Provides a perovskite lattice framework with adjustable mismatch for ABO3 films, improving crystallinity, orientation, and phase purity compared with amorphous or mismatched supports.
  • Strain engineering: The intermediate lattice parameter allows tuning of biaxial strain to stabilize metastable phases (e.g., tetragonal/monoclinic distortions in ferroelectrics, altered bandwidths in correlated oxides).
  • Interface control: Atomically flat terraces (with controlled miscut) promote step-flow growth; enables interface phenomena studies (2DEGs, exchange bias, interfacial ferroelectricity) when combined with suitable films.
  • Process compatibility: Chemically and thermally robust in oxidizing ambients, compatible with PLD/MBE/sputtering routines and post-deposition anneals.
  • Device integration: Electrical insulation and optical transparency support capacitor stacks, microelectronic test structures, and optoelectronic characterizations without substrate-induced conduction or absorption. Note: Specific orientation, polish, and termination—which critically impact synthetic outcomes—are not provided for this item; consult the CoA and perform pre-growth AFM/XRD checks.
Target Specificity

Not applicable. This product is not a biological targeting reagent (e.g., antibody, ligand, probe). There are no antigen/epitope or species reactivity details associated with LSAT substrates.

Shall we send you a message when we have discounts available?

Remind me later

Thank you! Please check your email inbox to confirm.

Oops! Notifications are disabled.