Certificats (CoA, COO, BSE/TSE et tableau d'analyse)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:
Calculateurs de solution
Molarity Calculator
Determine the necessary mass, volume, or concentration for preparing a solution.
Dilution Calculator
Determine the dilution needed to prepare a stock solution.
Reconstitution Calculator
Avis
Avis des clients
Application Protocols
No vendor-tested application protocols are specified for A2-Iso5-4DC19. The following generalized workflows are commonly used for small-molecule library members and should be adapted to your assay’s requirements.
Preparation of stock solutions (general):
Bring vial to room temperature inside a desiccator to avoid condensation.
Weigh quickly, cap promptly. Dissolve in DMSO to 10–50 mM. Vortex and sonicate as needed. If insoluble, try DMF or ACN.
Optionally sterile-filter (0.22 µm PTFE) for cell-based assays if compatible.
Plate handling for HTS:
Dispense DMSO stocks into low-bind polypropylene plates; seal with solvent-resistant films.
For aqueous dilution, use multichannel or acoustic dispensing to achieve target final concentrations with ≤0.5–1% DMSO (assay-dependent).
Include vehicle controls and, when available, a known active control.
Stability checks:
Inspect for precipitation upon dilution. If observed, increase DMSO fraction slightly within assay tolerance or reduce target concentration.
Confirm identity/purity by LC–MS before and after screening campaigns when results are decision-enabling.
Note: These are general research practices. For GLP/GMP or regulated environments, develop and validate method-specific SOPs.
Biological Roles
Item-specific biological roles, targets, or pathway interactions for A2-Iso5-4DC19 are not provided.
No target annotations, mode-of-action data, or pathway membership are supplied in the product data.
As with many discovery library compounds, any biological role is context-dependent and determined experimentally within your assay system.
General guidance for evaluating biological roles (research context only):
Profile across orthogonal assays to confirm on-target effects and rule out assay interference (e.g., fluorescence quenching, redox cycling, aggregation). Incorporate counterscreens and detergent controls for PAINS-like behavior when applicable.
Determine basic ADME properties (solubility in assay buffer, stability in storage matrix, microsomal stability) to discern whether observed effects are exposure-limited.
Use concentration–response curves and appropriate statistics (Hill slopes, outlier handling) for robust potency estimates.
Important: No clinical or therapeutic claims are made or implied. This product is supplied strictly for research use; any biological role must be established by the end user.
Buffer Applications
A2-Iso5-4DC19 is not a buffering reagent. However, small molecules from libraries are commonly introduced into aqueous assay buffers from DMSO stock solutions.
Practical tips (general):
Prepare a concentrated DMSO stock (e.g., 10–50 mM). Immediately before use, dilute into the assay buffer (HEPES, PBS, Tris, etc.) to the required final concentration while maintaining an acceptable final DMSO level (commonly ≤0.5–1% v/v; confirm assay tolerance).
Add compound last to minimize precipitation when mixing with proteins or salts. If cloudiness occurs, increase dilution time, mix gently, or raise temperature slightly (room temperature) before final readout.
When working at very low DMSO levels, pre-dilute the DMSO stock into intermediate solvent–buffer mixes to avoid local supersaturation.
Compatibility notes (general):
High salt and certain detergents can alter solubility; check for precipitation visually and by light scattering.
Adsorption to plastics can occur for lipophilic compounds; use low-bind polypropylene plates/tubes and include surfactants only if assay-compatible.
No item-specific buffer recipes or pKa data are available; consult the CoA/Spec Sheet if buffer guidance is provided for this item.
Green Alternatives
A2-Iso5-4DC19 is a small-molecule library member, not a bulk solvent or commodity reagent. Green chemistry considerations therefore center on the choice of dissolution vehicle and analytical/mobile phases rather than replacing the compound itself.
Greener solvent considerations (general):
Prefer water-based buffers with minimal organic co-solvent where assay biology allows.
Use ethanol or isopropanol in place of methanol where compatible (lower toxicity), acknowledging possible differences in solubility and protein effects.
Consider 2-MeTHF or CPME for workups/dry-down steps over chlorinated solvents when volatility and safety are acceptable for your process.
Brief comparison (general, literature-based):
DMSO vs. DMF: DMSO offers broad solvency with a better EHS profile than DMF; choose DMSO for stock solutions when possible.
ACN vs. MeCN/MeOH blends (LC): Reducing neat ACN consumption by using ACN–water gradients efficiently or partial replacement with MeOH can lower environmental impact (method-dependent).
Operational practices to reduce footprint:
Scale down assays (µL range), employ sealed plates to reduce solvent loss, and consolidate analytical runs.
Reuse HPLC eluents where validated and dispose of solvent waste via approved channels.
Item-specific greener substitutes are not applicable due to the compound’s identity and function; focus instead on greener solvents and miniaturized workflows.
Pharmaceutical Uses
No pharmacopeial status, excipient role, or formulation usage is specified for A2-Iso5-4DC19.
This product is supplied for research use only and is not intended for human or veterinary administration.
As a discovery library member, its principal role is in early-stage research such as hit identification and SAR exploration, not in GMP manufacturing or clinical formulation.
General R&D formulation context (non-clinical):
For in vitro research, DMSO stock solutions are standard. For pre-formulation screening (if permitted by institutional policy), cosolvent systems (e.g., PEG400/EtOH/saline) or lipid-based vehicles are sometimes explored to assess exposure in model systems; such work remains strictly non-clinical.
If progressing toward rigorous developability assessments, generate compound-specific data (solubility, stability, pKa, logD, solid form) under quality systems appropriate to your stage.
No claims of therapeutic use are made or implied. Refer to institutional guidelines and do not use in humans or animals.
Physical Properties
Item-specific physicochemical data have not been provided for A2-Iso5-4DC19.
Appearance: Not specified for this item; refer to CoA/Spec Sheet.
Melting/Boiling Point: Not specified for this item; refer to CoA/Spec Sheet.
Density/Refractive Index: Not specified for this item; refer to CoA/Spec Sheet.
LogP, pKa, PSA, HBD/HBA: Not specified for this item; refer to CoA/Spec Sheet.
Solubility: Not specified for this item; refer to CoA/Spec Sheet.
General guidance for unknown small molecules (literature/practice-based):
For dissolution trials, begin with high-solvency vehicles: DMSO, DMF, or acetonitrile. If solubility is acceptable, back-titrate into assay buffers (final organic ≤0.5–1% v/v as assay permits).
For solids with ambiguous properties, a tiered solvent screen (DMSO → DMF → MeOH/EtOH → ACN → aqueous with mild co-solvent) is efficient. Sonication and gentle warming (≤40 °C) can help. Avoid prolonged heating of reactive motifs.
If the item is supplied as a film or amorphous solid, hygroscopicity may affect measured mass; equilibrate to room temperature in a desiccator before opening to minimize moisture uptake.
Note: For any property values required for modeling or LC method development (e.g., UV λmax, extinction, pKa), please obtain the CoA/Spec Sheet or characterize in-house.
Quality and Grades
Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.
How to interpret grades (general guidance):
For screening library members, vendors commonly provide screening grade or research grade material, typically with HPLC purity reporting (e.g., area % at 254 nm) and mass identity confirmation (ESI-MS/HRMS). In the absence of a listed grade, request the CoA for purity, chromatogram, and identity data.
If your work is bioassay-sensitive (e.g., ligand profiling), consider setting an internal acceptance criterion (e.g., ≥95% HPLC area, single major peak; residual solvents and water within your thresholds).
Analytical documentation (what to expect/ask for):
Identity: MS and, when available, 1H NMR.
Purity: HPLC/UPLC with UV trace and conditions.
Form: Solid vs. oil/film; salt form if applicable.
Residuals: Water (KF) and residual solvents—often reported but not guaranteed unless specified.
Stabilizers/additives:
None stated for this item. If stabilizers or salt forms are critical for your workflow (e.g., TFA vs. HCl salt), request explicit confirmation on the CoA.
Practical tip:
Upon receipt, run a quick incoming QC (LC–MS, purity check) aligned to your assay wavelength to ensure UV response and retention time are suitable for your platform.
Reaction and Applications
This product is categorized within a small-molecule/compound library and is typically used for discovery workflows rather than as a general synthetic reagent. No manufacturer applications are provided beyond research use.
Typical research applications (general):
Primary and secondary screening: Evaluate as a test article in biochemical or cell-based assays to identify activity profiles or SAR starting points.
Reference standard: Analytical calibration or positive/negative control once activity is established within a project.
Profiling: Solubility, stability, permeability (PAMPA/Caco-2), and microsomal stability measurements to inform developability.
If the compound is repurposed in synthesis:
Without structure/functionality, no specific reaction roles can be recommended. In general, library members are not optimized as reagents or catalysts and may contain sensitive motifs.
Practical handling in screening campaigns:
Prepare DMSO master stocks (e.g., 10 mM), verify clarity, and store aliquots at −20 °C to avoid freeze–thaw cycles.
Track concentration and volume in plates/vials; compensate for DMSO evaporation with sealing and controlled humidity.
Confirm identity/purity by LC–MS before critical decision-making to avoid activity artifacts.
Note: Absent structural data, no mechanistic or named reaction guidance is applicable. For specific application expansion, please request the CoA/Spec Sheet or share structure internally.
Reaction Conditions
No reaction conditions are provided for A2-Iso5-4DC19, and in the absence of structural data, specific chemistry cannot be recommended.
General notes (non-item-specific):
If you determine the structure and seek to derivatize it, choose conditions aligned with its functional groups (e.g., amide couplings under HATU/DIPEA in DMF; Suzuki couplings in mixed aqueous–organic media with Pd catalysts; nucleophilic substitutions under polar aprotic conditions). These are purely illustrative and must be adapted to the confirmed structure.
For sensitive motifs, consider inert atmosphere, anhydrous solvents, and low temperatures.
Always perform small-scale scouting reactions and monitor by LC–MS.
Because neither the functional groups nor stability domains of A2-Iso5-4DC19 are known, treat it cautiously with respect to base, acid, heat, and oxidants until compatibility is established experimentally.
Safety and Handling
Safety classification data specific to A2-Iso5-4DC19 have not been provided in the listing.
Signal Word / GHS Classification / H-Statements / Pictograms: Not specified for this item; refer to SDS.
Recommended storage: Store at −20 °C (per product data). Shipments are made with ice chest + ice pads to preserve integrity during transit.
General laboratory precautions (defer to SDS as authoritative):
PPE: Lab coat, safety glasses, and appropriate chemically resistant gloves (e.g., nitrile). Use in a fume hood to avoid inhalation of dusts/vapors/aerosols.
Hygiene: Avoid skin/eye contact. Do not ingest or inhale. Wash thoroughly after handling. Keep containers tightly closed.
Incompatibilities (general): Unknown for this item. As a precaution, segregate from strong oxidizers/acids/bases until compatibility is known.
Spill/accidental release: Contain solids with inert absorbent, avoid dust formation, and collect for disposal per institutional policy.
First aid (overview): If inhaled—move to fresh air; if on skin—wash with soap/water; if in eyes—rinse with water for several minutes; if ingested—seek medical advice. Always consult the SDS for compound-specific actions.
Special notes for discovery compounds:
Avoid repeated freeze–thaw of stock solutions; aliquot to minimize degradation.
Light and moisture sensitivity are unknown—protect from light and store in a desiccated environment unless otherwise specified.
Regulatory note: For research use only; not for human or veterinary use.
Solvent Selection
Because structural details are not provided, solvent choice should be made empirically with a short, tiered screen suitable for small-molecule library members.
Recommended dissolution strategy:
Start with DMSO (high solvency, assay-friendly at ≤0.5–1% v/v final). If insoluble, try DMF or acetonitrile.
For polar/ionizable compounds, evaluate methanol or ethanol; for lipophilic materials, consider 2-MeTHF or isopropanol as intermediates before final dilution.
Prepare concentrated stocks (e.g., 10–50 mM in DMSO), then back-dilute into assay buffer while keeping final organic content within assay tolerances.
Best practices for small-molecule library members (general):
Keep material in a tightly sealed container under dry, inert atmosphere if possible. Use a desiccant in secondary containment to limit humidity exposure.
Allow the container to equilibrate to room temperature before opening to reduce moisture condensation, then promptly re-seal.
Prepare single-use aliquots of DMSO stock (e.g., 10–50 mM) to minimize freeze–thaw cycles; store aliquots at −20 °C in amber vials/plates if light sensitivity is suspected.
Avoid repeated exposure to ambient light and air; purge headspace with nitrogen/argon if feasible.
Reconstitution guidance:
Solvent choice is item-dependent; start with DMSO and escalate to DMF or ACN if needed. Gentle warming (≤40 °C) and sonication can aid dissolution.
Verify clarity and concentration (by weight and/or UV/LC–MS) before use in critical assays.
Shelf-life and stability:
Not specified for this item; refer to CoA/Spec Sheet. If stability is unknown, adopt a conservative approach (limited storage duration for solutions, retain solid as primary reference).
Structure and Identity
Brief overview: A2-Iso5-4DC19 is listed as a small-molecule library member. Detailed structural identifiers are not supplied in the product data.
Product Name: A2-Iso5-4DC19 (SKU: A1439888)
CAS: 2412492-19-2
SMILES: Not specified for this item; refer to CoA/Spec Sheet.
InChIKey: Not specified for this item; refer to CoA/Spec Sheet.
Molecular Formula: Not specified for this item; refer to CoA/Spec Sheet.
Molecular Weight: Not specified for this item; refer to CoA/Spec Sheet.
Structural features (general note):
Specific functional groups, ring systems, and stereochemistry are not provided in the current listing. Without a structure, a 2D description cannot be rendered.
If you require structural identifiers (SMILES/InChI), please request the latest CoA/Spec Sheet; these are often provided for library compounds upon request under the terms of use.
Context for small-molecule libraries (general):
Compounds in discovery libraries typically encompass diverse scaffolds (heteroaromatics, saturated N-heterocycles, biaryl motifs, and sp3-rich frameworks) designed for lead finding and SAR expansion.
Researchers commonly maintain a tracked internal ID ↔ CAS/SMILES mapping for plate and vial management; we recommend associating A2-Iso5-4DC19 with your ELN/sample registry upon receipt.
Synthetic Utility
Specific synthetic functions for A2-Iso5-4DC19 cannot be described without structural information.
No functional group data, reactivity, or protecting group compatibility is available in the product data.
Library compounds are generally intended as test articles rather than reagents, catalysts, or building blocks.
General considerations if used synthetically (contextual, not item-specific):
Verify identity and purity by LC–MS/NMR prior to any transformation to ensure material suitability.
If attempting derivatizations (e.g., for SAR expansion), determine the presence of modifiable handles (amines, acids, halides) via analytical characterization before planning reactions.
Track batch provenance; subtle impurity profiles can confound reaction outcomes.
For retrosynthetic planning and reaction design, please obtain the SMILES/InChI or a structural rendering via the CoA/Spec Sheet.
Target Specificity
No target, binding partner, or biochemical specificity is provided for A2-Iso5-4DC19.
There is no antigen/epitope information (not an antibody or protein reagent).
No enzyme, receptor, or pathway specificity data are available in the product data.
For discovery use, researchers should establish target engagement experimentally using appropriate assays (e.g., biochemical activity, biophysical binding such as SPR/DSF/ITC, chemical proteomics) and include orthogonal counterscreens to exclude non-specific effects.
Foire aux questions
How should this product be stored?
Store at ?20 °C. Freezer storage is required to maintain the specified shelf life.
How is this product shipped?
This product ships in an insulated container with ice pads. Unpack on arrival and transfer it to the storage condition stated above.
What are the CAS number, molecular formula and molecular weight?
The CAS Number is 2412492-19-2, the molecular formula is C49H87N3O2, and the molecular weight is 750.23 g/mol.
What documentation is provided?
Available product documentation, including Certificates of Analysis (COA), Safety Data Sheets (SDS), and specification sheets, is shown in the product document area. Document availability and access follow the current site policy.
Nous utilisons des cookies pour garantir le bon fonctionnement du site et, lorsque cela est autorisé, pour améliorer votre expérience. Vous pouvez gérer vos préférences à tout moment dans les Paramètres. Pour en savoir plus, consultez notre Politique relative aux cookies.
Souhaitez-vous que nous vous envoyions un message lorsque des réductions seront disponibles?
Me rappeler plus tard
Merci ! Veuillez vérifier votre boîte de réception e-mail pour confirmer.
Products are supplied to verified businesses, institutions, and qualified professionals for research and development use only. Not for use in humans, animals, diagnosis, or therapy.
