N2300

Cat. No.: N487529
DISPONIBLE À COMMANDE
Storage
Room temperature
★
Taille
USA
Allemagne (EU)*
Prix
Qté
100mg
N487529-100mg
Sur commande · 8–12 semaines

1 040,90$US

1 214,90$US
Enregistrer 174,00 $US (14.32%)
500mg
N487529-500mg
Sur commande · 8–12 semaines

4 160,90$US

4 859,90$US
Enregistrer 699,00 $US (14.38%)
Enter a quantity for the sizes you want to add.

Spécifications

Conditions de stockage de stockage
Room temperature

Données avancées

Certificats (CoA, COO, BSE/TSE et tableau d'analyse)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:
Propriétés chimiques et physiques
Solubilitéanisole: soluble; chloroform: soluble; dichlorobenzene: soluble; toluene: soluble; xylene: soluble
Calculateurs de solution
Avis

Avis des clients

Application Protocols

No validated, item-specific protocols are provided for this product on this page.

  • Item-specific tested applications: Not specified for this item; refer to CoA/Spec Sheet.
  • General protocol development advice (materials science):
    • Define the objective metric (e.g., film uniformity, conductivity, adhesion, catalytic turnover) and create a DoE screening plan.
    • Standardize sample preparation (drying, milling/sieving for powders; filtration for solutions; degassing as needed).
    • Control environmental factors: humidity, temperature, solvent purity, and substrate conditioning.
    • Implement QA/QC checkpoints: spectral fingerprints (FT-IR/UV–Vis), thermal analysis (DSC/TGA), and performance tests aligned to your application.
    • Record lot numbers and instrument calibration status to enable reproducibility and traceability.

All procedures should be validated in your lab with appropriate controls. Research use only.

Biological Roles

This product is listed under materials science and is intended for research use only. No biological identity or function is provided for this item.

  • Item-specific biological information: Not specified for this item; refer to CoA/Spec Sheet.
  • General note:
    • Unless the material is a defined biochemical or biomaterial (e.g., peptide, polysaccharide, bio-derived polymer), it typically has no intrinsic biological role in cellular metabolism or signaling.
    • If the material is intended for biointerface studies (e.g., coatings, scaffolds), characterize cytocompatibility and protein adsorption in controlled in vitro assays before use. This does not imply suitability for medical or clinical use.

All uses are for research and laboratory purposes only; no clinical or diagnostic claims are made.

Buffer Applications

Buffer preparation guidance is generally not applicable because the identity and acid/base properties of this item are not provided.

  • Item-specific buffer use: Not specified for this item; refer to CoA/Spec Sheet.
  • General note:
    • If the material is water-soluble and used in aqueous systems, evaluate pKa(s) and ionic strength effects before incorporating into any buffered formulation.
    • For colloids or dispersions, buffers can influence zeta potential and stability; perform screening across pH and ionic strengths to identify optimal conditions.

For definitive buffer recipes and pH ranges, use well-characterized systems (e.g., phosphate, HEPES, acetate) unrelated to this unspecified item.

Green Alternatives

Without item-specific identity, green recommendations are presented as general guidance aligned with the 12 Principles of Green Chemistry and common materials processing needs.

  • Solvent and process substitutions (general, literature):
    • Replace chlorinated/aromatic solvents with ethyl acetate, propylene carbonate, dimethyl carbonate, 2-MeTHF, CPME, or water when feasible.
    • Use mechanochemistry, solvent-free melt processing, or supercritical CO2 for certain polymerizations or extractions to minimize VOCs.
    • Opt for photochemical or electrochemical routes over stoichiometric oxidants/reductants where compatible.
  • Materials selection considerations:
    • Favor bio-based monomers/polymers (PLA, PHA, bio-epoxies) or recyclable thermoplastics over thermosets when life-cycle permits.
    • Select low-toxicity salts/ionic liquids (e.g., cholinium-based) for specialized tasks, validating performance and workup.
    • Minimize heavy-metal catalysts; consider Earth-abundant alternatives (Fe, Ni, Cu) and ligand systems enabling low loading.
  • Comparative view (illustrative):
    • Legacy solvent: DMF/DMAc → Alternative: Cyrene, NBP, propylene carbonate (check solubility/kinetics).
    • Legacy ether: THF → 2-MeTHF/CPME (lower peroxide formation rate; still monitor peroxides, literature).
    • Legacy aromatic: Toluene → EtOAc/Me-THF where polarity gap allows.
  • Implementation tips:
    • Pilot greener options at lab scale; benchmark yield, selectivity, film morphology, and device performance against legacy processes.
    • Conduct EHS and waste assessments to ensure genuine impact reduction, not burden-shifting.
Pharmaceutical Uses

No pharmaceutical or excipient status is provided for this item, and it is sold strictly for research use only.

  • Item-specific pharmacopeial status: Not specified for this item; refer to CoA/Spec Sheet.
  • General guidance (non-clinical, non-therapeutic):
    • Materials deployed in pharmaceutical development must meet compendial (USP/EP/JP) or ICH-aligned impurity and elemental limits, residual solvent controls, and microbiological standards.
    • If an analogous material is considered for formulation research, assess extractables/leachables, particulate burden, and bioburden/endotoxin as appropriate for lab feasibility only.
    • For device or packaging research, evaluate compatibility with actives and other excipients under accelerated and long-term storage per ICH Q1 conditions.

This product is not intended for human or veterinary use, diagnostic procedures, or as a drug substance/excipient.

Physical Properties

Item-specific physical constants are not provided here. Use the product’s CoA/Spec Sheet for authoritative values and test methods.

  • Item-specific values:
    • Appearance: Not specified for this item; refer to CoA/Spec Sheet.
    • Melting/softening point: Not specified for this item; refer to CoA/Spec Sheet.
    • Boiling point / decomposition temp.: Not specified for this item; refer to CoA/Spec Sheet.
    • Density / specific gravity: Not specified for this item; refer to CoA/Spec Sheet.
    • Solubility profile: Not specified for this item; refer to CoA/Spec Sheet.
    • Refractive index / optical properties: Not specified for this item; refer to CoA/Spec Sheet.
    • Vapor pressure / volatility: Not specified for this item; refer to CoA/Spec Sheet.
  • Practical characterization approaches (general, literature):
    • Use TGA/DSC to determine thermal stability, Tg/Tm, and enthalpic transitions for polymers and hybrid materials.
    • Establish solubility/miscibility by micro-screening across a solvent panel (e.g., water, alcohols, ethers, esters, aromatics, chlorinated, polar aprotics). Hansen or Kamlet–Taft parameters can guide selection (literature).
    • For nanopowders, characterize BET surface area (N2 adsorption), particle size (DLS, TEM), and tap density.
    • For optoelectronic materials, measure UV–Vis, PL, and if applicable, conductivity/carrier mobility (four-point probe, Hall effect).
  • Notes:
    • Many advanced materials exhibit decomposition before boiling; report onsets and mass loss steps (TGA) rather than conventional BP (general literature).
    • Hygroscopic or air-sensitive materials require controlled-atmosphere handling; verify with mass gain vs RH or O2 exposure tests (general guidance).
Quality and Grades

Grade/purity details for this specific item are not listed here. Refer to the product CoA/Spec Sheet for analytical results and acceptance criteria.

  • Item-specific information:
    • Grade/purity: Not specified for this item; refer to CoA/Spec Sheet.
    • Stabilizers/additives: Not specified for this item; refer to CoA/Spec Sheet.
  • How to interpret common grades (general guidance):
    • Analytical/AR grade: Tight impurity limits intended for analytical work; low residue and well-defined assays.
    • HPLC/LC–MS grade solvents: Very low UV absorbance and low metal/ionic background for trace analysis.
    • Electronic/semiconductor grade: Ultra-trace metal control (ppb–ppt) and low particulate burden for device fabrication.
    • Reagent grade: Suitable for general synthesis; broader impurity limits than AR.
    • Polymer grade metrics: Report Mn/Mw/Ð, residual monomer/solvent, ash, moisture, and stabilizer content.
  • Recommended QC checkpoints (applicable to materials science reagents):
    • Identity: FT-IR, NMR (if organic), XRD (if crystalline), or XPS (surface chemistry).
    • Purity & composition: Titration/assay, GC/LC, ICP-OES/MS for metals, TGA for volatiles and stabilizers.
    • Performance: Application-specific tests (e.g., film formation, conductivity, catalytic activity) with defined acceptance windows.
  • Documentation: Ensure lot-specific CoA includes test methods, specifications, and results. For critical use (electronics, energy), request expanded impurity profiling (metals, halides, ionic residues) as required.
Reaction and Applications

The catalog entry does not include application details. Below is general, materials-focused guidance to help frame potential uses, subject to confirmation with the actual product identity and CoA.

  • Materials science application spaces (general):
    • Coatings/films: Binders, crosslinkers, or functional additives for barrier, dielectric, or optical layers.
    • Composites: Matrix resins or surface treatments for fillers/fibers to enhance adhesion, toughness, or conductivity.
    • Energy materials: Precursors or additives for batteries, fuel cells, photovoltaics, or supercapacitors (e.g., ionic conductors, redox shuttles, dopants).
    • Catalysis: Supports, ligands, or precatalysts for heterogeneous/homogeneous systems.
    • Nanotechnology: Particle precursors, surface ligands, or self-assembly modulators.
  • If used in synthesis (general reaction contexts):
    • Organic transformations may require anhydrous/oxygen-free conditions; validate compatibility with bases, acids, and transition metals.
    • For polymer chemistry, determine reactivity ratio, crosslinking mechanism (radical, cationic, anionic), and inhibitor profile, if any.
  • Practical tips:
    • Run a small-scale feasibility test to benchmark solubility/reactivity; track by GC/LC/SEC or spectroscopic methods.
    • Establish thermal windows by DSC/TGA before scale-up to avoid premature curing or decomposition.
    • For functional additives, perform dose–response studies to map performance vs. loading, and check for phase separation or crystallization during aging.

Note: All uses are for research and laboratory purposes only.

Reaction Conditions

No item-specific reaction conditions are available for this product. The following general practices help define suitable conditions when working with unknown or newly sourced materials.

  • Scouting experiments (general):
    • Conduct microscale trials (10–100 mg or mL) to probe solubility, stability, and preliminary reactivity.
    • Map temperature windows by DSC/TGA (for solids/polymers) or by isothermal holds to detect decomposition or volatilization.
    • Assess acid/base and redox tolerance using small aliquots under representative conditions.
  • Atmosphere and moisture:
    • For moisture- or air-sensitive materials, use Schlenk or glovebox techniques; dry solvents and apply inert gas sparging.
  • Kinetics and monitoring:
    • Monitor by GC/LC, in situ IR/Raman, or NMR where applicable; for polymerizations, track conversion and molecular weight growth (GPC/SEC).
  • Representative solvent classes (selection guidance only):
    • Polar aprotics (DMSO, DMF, MeCN), ethers (THF, 2-MeTHF, CPME), esters (EtOAc), aromatics (toluene), alcohols (MeOH/EtOH), water.
  • Workup and isolation:
    • Choose quench protocols that avoid exotherms and unwanted side reactions; for sensitive materials, use low-temperature quenches and buffered systems.
    • For films/coatings, control drying rate and residual solvent to achieve target morphology.

All values/conditions above are general literature practices and must be confirmed experimentally for the actual material.

Safety and Handling

Safety data for this specific item have not been provided on this page. Always consult the product-specific SDS for definitive guidance.

  • Item-specific hazard data:
    • Signal word: Not specified for this item; refer to SDS.
    • GHS classification & pictograms: Not specified for this item; refer to SDS.
    • H-statements: Not specified for this item; refer to SDS.
  • General laboratory precautions (good practice):
    • Wear appropriate PPE: lab coat, safety glasses, and chemically resistant gloves; consider a face shield and additional protection if dusts/fumes may form.
    • Handle powders and volatile materials in a certified fume hood; minimize aerosol and dust generation.
    • Avoid incompatible materials until verified by SDS (strong oxidizers/reducers, acids/bases, water for moisture-sensitive reagents, halogens, and peroxides as applicable).
    • For unknowns, assume potential for skin/eye irritation and respiratory sensitization; use local exhaust and avoid skin contact.
  • First-aid overview (non-specific; defer to SDS):
    • Inhalation: Move to fresh air; seek medical attention if symptoms persist.
    • Skin/eye contact: Rinse with water for at least 15 minutes; remove contaminated clothing; obtain medical advice.
    • Ingestion: Rinse mouth; do not induce vomiting; seek medical attention.
  • Spill & disposal (general):
    • Contain and collect with inert absorbent or HEPA-filtered vacuum for powders; dispose via licensed waste contractor per local regulations.
  • Storage per Product Data: Room temperature. Keep container tightly closed; protect from moisture, heat, and light unless CoA specifies otherwise.
Solvent Selection

Solvent selection depends on the unknown identity and intended use. The following general framework helps determine an appropriate medium for processing or reaction.

  • Decision framework (general):
    • Start with a solubility screen across a polarity gradient: water, alcohols, acetone/MEK, acetonitrile/DMF/DMSO, ethers (THF/MTBE/CPME), esters (EtOAc), aromatics (toluene), and alkanes.
    • Use Hansen solubility parameters (HSP) or Snyder polarity indices to rationalize compatibility and to identify cosolvent blends.
    • For ionic or highly polar species, consider protic (water/alcohols) or polar aprotic solvents; for hydrophobic polymers/materials, aromatic or etheric media often help.
    • For moisture/air-sensitive reagents, select rigorously dried and deoxygenated solvents; consider glovebox or Schlenk line techniques.
  • Processing considerations:
    • Film/coating applications benefit from a boiling point ladder and vapor pressure control to tune drying profiles and morphology.
    • For nanoparticle dispersions, choose solvents compatible with surface ligands, and adjust ionic strength/pH (if aqueous) to maintain colloidal stability.
    • Consider viscosity and surface tension for printing/spin-coating; add high-boiling cosolvents as needed for wetting control.
  • Green chemistry note (literature): Prefer 2-MeTHF, CPME, propylene carbonate, dimethyl carbonate, ethyl acetate, or water when feasible; avoid chlorinated solvents unless performance requires them. Validate that greener choices meet performance and purity needs for the specific formulation.
Storage and Reconstitution

Storage conditions provided in Product Data indicate room temperature. Additional details should be taken from the item’s CoA/SDS once identity is known.

  • Item-specific storage:
    • Storage temperature: Room temperature (per Product Data).
    • Container: Keep tightly closed in the original container. Use amber/light-resistant packaging if the CoA/SDS indicates photosensitivity. For moisture- or air-sensitive items, consider secondary containment with desiccant or inert-gas backfill.
    • Stability: Not specified for this item; refer to CoA/Spec Sheet.
    • Shipping: Not specified for this item; refer to CoA/Spec Sheet.
  • Reconstitution/dispersion (general guidance):
    • For solids: Start with a small-volume solvent screen; apply sonication or gentle heating below any known decomposition onset (if available) to aid dissolution or dispersion.
    • For powders/nanomaterials: Wet with a good solvent or appropriate dispersant; use probe or bath sonication in short pulses to avoid overheating.
    • For liquids/viscous materials: Prewarm to reduce viscosity; mix thoroughly and, if needed, filter (0.2–0.45 µm) to remove particulates.
  • Shelf-life management:
    • Label with receipt date and opening date; track lot numbers.
    • Minimize headspace and repeated exposure by aliquoting.

Always prioritize the product-specific SDS/CoA for final storage and handling instructions. Research use only.

Structure and Identity

Brief note: The structural identity for this catalog item is not disclosed on this page. The guidance below outlines how professionals typically document and verify materials used in materials science research.

  • Item-specific identifiers:
    • Chemical name: Not specified for this item; refer to CoA/Spec Sheet.
    • CAS: Not specified for this item; refer to CoA/Spec Sheet.
    • Molecular formula: Not specified for this item; refer to CoA/Spec Sheet.
    • Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.
    • SMILES / InChI / InChIKey: Not specified for this item; refer to CoA/Spec Sheet.
  • Structural features (general guidance):
    • If the material is an organic small molecule, document functional groups (e.g., alcohol, amide, halide), ring systems, and any stereogenic centers.
    • If it is a polymer, capture repeat unit, average molecular weight (Mn/Mw), Ð (PDI), end-group identity, and tacticity if relevant.
    • For inorganic/ceramic materials, specify phase/stoichiometry (e.g., perovskite ABO3), oxidation state, and crystallinity.
    • For nanostructures, report core composition, shell/ligand chemistry, size distribution, and surface area.
  • 2D structure description (general): Summarize backbone (aliphatic/aromatic/inorganic), key heteroatoms (O, N, S, halogens), and any conjugation or ionic moieties that affect solubility and reactivity.
  • Identity verification (recommended workflow):
    • Organic/small-molecule: 1H/13C NMR, HRMS, FT-IR, elemental analysis.
    • Polymers: GPC/SEC (Mn, Mw, Ð), NMR for repeat unit, MALDI for end groups.
    • Inorganic/nanomaterials: XRD (phase), XPS (surface chemistry), TEM/SEM (morphology), ICP-OES (composition).
Synthetic Utility

The synthetic role of this specific item cannot be stated without structural information. The following outlines common synthetic utilities of materials-focused reagents in research settings.

  • Potential roles (general):
    • Monomers/Crosslinkers: Enable thermoset or thermoplastic network formation via radical, cationic, anionic, or condensation mechanisms.
    • Catalysts/Ligands: Facilitate C–C, C–N, or polymerization reactions (e.g., cross-coupling, ATRP, ROMP), or serve as supports.
    • Precursors: Provide metal/oxide/chalcogenide sources for nanoparticles, MOFs/COFs, or ceramic phases.
    • Dopants/Additives: Modulate conductivity, dielectric constant, glass transition, or morphological control in thin films.
  • Practical considerations:
    • Validate compatibility with bases/acids/oxidants/reductants and transition metals before multi-step sequences.
    • Establish purification pathways (recrystallization, distillation, chromatography, trituration) suitable for the material class; for polymers, use precipitation fractionation or dialysis.
    • Track impurity profiles (metals, halides, counterions, inhibitors) that can poison catalysts or alter device performance.

All guidance above is general and must be tailored once the chemical identity is known.

Target Specificity

Not applicable. This product is not described as a biological macromolecule (e.g., antibody, enzyme, nucleic acid) and has no disclosed biological target.

  • Item-specific target information: Not specified for this item; refer to CoA/Spec Sheet.

Souhaitez-vous que nous vous envoyions un message lorsque des réductions seront disponibles?

Me rappeler plus tard

Merci ! Veuillez vérifier votre boîte de réception e-mail pour confirmer.

Oups ! Les notifications sont désactivées.