JYBL-Ⅱ Decalcifying Solution - BioReagent

Cat. No.: J1529419
注文可能
グレード&純度 BioReagent ? BioReagent grade — tested suitable for life-science and molecular-biology use. Use for cell culture, assays, and biochemical work needing biological compatibility.
Storage
Room temperature
Shipped In
Normal
Application
855
★
サイズ
USA
ドイツ (EU)*
価格
個数
500ml
J1529419-500ml
受注生産 · 8~12週間
$50.90
Enter a quantity for the sizes you want to add.

概要

During tissue sectioning, some tissues contain bone or calcified foci. Calcified tissues are not suitable for direct paraffin embedding and sectioning, because the density difference between calcium and paraffin makes it difficult to obtain intact sections. For calcified tissues, it is best to fix first and then decalcify, or perform both simultaneously, followed by downstream procedures such as dehydration, clearing, paraffin infiltration, embedding, and sectioning. Many reagents are available for decalcification, including organic acids, inorganic acids, ethylenediaminetetraacetic acid (EDTA), and electrolytic decalcification. EDTA is a relatively good chelating decalcifying agent, with minimal impact on tissue structure and good preservation of certain enzymes in tissues. Tissues decalcified with EDTA can be used for immunohistochemistry and in situ hybridization staining; however, this method is too slow, generally taking several weeks to months.

JYBL-Ⅱ Decalcifying Solution is mainly composed of dilute acid, formaldehyde, formic acid, etc. Its advantages are:

①rapid action, shorter than JYBL-I, generally completing within 24 hours;

② minimal damage to tissue structure;

③ complete decalcification.

This decalcifying solution is particularly suitable for routine decalcification of bone tissue specimens in pathology departments, but it is not suitable for determining the decalcification endpoint by chemical methods, and it causes some damage to tissue structure.

This reagent is intended for research use only and is not suitable for clinical diagnosis or other applications.

Product Series Overview

Cat. No.Product NameMain ComponentsDecalcification TimeTissue Damage RiskCore AdvantagesApplicable Specimen Types
J1525466JYBL-Ⅰ Decalcifying SolutionDilute acid, formaldehyde, formic acid24–36 hRelatively lowBalanced speed and tissue preservationRoutine bone tissue specimens
J1529419JYBL-Ⅱ Decalcifying SolutionDilute acid, formaldehyde, formic acidApprox. 24 h (faster than Ⅰ)Moderate (slightly higher than Ⅰ)Faster decalcification than ⅠRoutine bone tissue specimens
J1529418JYBL-Ⅲ Decalcifying SolutionFormaldehyde, 50% formic acidRoom temperature: 2–3 daysRelatively minimal (formic acid is the mildest)Minimal tissue damage; superior morphology preservationSpecial bone tissue specimens
J1529417JYBL-Ⅳ Decalcifying SolutionFormaldehyde, formic acid (acid-free formulation)37°C incubation: 2–3 hRelatively low; temperature control requiredFastest decalcification; designed for bone marrow biopsyBone marrow biopsy specimens

Materials Required (Self-Prepared):

1.Distilled water or PBS

2.Heating apparatus or microwave oven, and dedicated decalcification container (glass)

 Operating Instructions (For Reference Only):

1.For bone tissue decalcification, the specimen should not be too thick; generally approximately 3–5 mm.

2.After fixation, wash the tissue 3 times with distilled water or PBS, 20 minutes each time.

3.Transfer the tissue to 20–30 volumes of JYBL-Ⅱ Decalcifying Solution and decalcify for 24 hours; to accelerate decalcification, it can be performed at 37°C.

4.Rinse several times with distilled water.

5.Proceed with routine dehydration and embedding.

Precautions:

1.For bone tissue blocks of 5 mm thickness, decalcification generally takes 24–36 hours.

2.Moderate heating can accelerate decalcification, but the temperature should generally not exceed 37–40°C. Excessive temperatures may cause loosening and disintegration of bone tissue; temperatures above 60°C must not be used.

3.Decalcification should be thorough to prevent under-decalcification or over-decalcification. The degree of decalcification should be controlled to ensure that tissue sectioning is not affected while shortening the decalcification time as much as possible, to avoid tissue damage caused by prolonged decalcification.

4.Avoid using metal containers for decalcification; glass containers are recommended.

5.Bone tissue should be fixed before decalcification, or fixation and decalcification performed simultaneously. Decalcification should not be performed before fixation, in order to reduce tissue damage.

6.Check the degree of decalcification periodically. Over-decalcification will increase tissue damage and affect staining results.

7.For your safety and health, please wear a lab coat and disposable gloves during handling.

Appendix:

Determination of Decalcification Endpoint (Physical Method): Use methods such as needling, pinching, or clamping. Decalcification can be terminated when the bone tissue becomes soft or when no resistance is felt upon needling. Physical detection methods may cause certain damage to tissue structure; therefore, excessive force or repeated testing should be avoided.

仕様

仕様と純度
BioReagent
安定性と保管
Store at Room temperature. long term (12 months).
保管条件
Room temperature
入荷
Normal
等級
BioReagent
Product Line
生物製品

詳細データ

証明書(CoA、COO、BSE/TSEと分析図)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:

Find and download the COA for your product by matching the lot number on the packaging.

1 results found

Lot NumberCertificate Type日付商品
ZJ26F1040101ZJ26F1040101Certificate of AnalysisOct 23, 2026 J1529419
よくある質問と記事
ソリューション計算機
レビュー

顧客レビュー

グレードの選択でお困りですか?

当社のグレード選定ガイドでは、カタログ内のすべてのバリエーションについて、純度、安定剤の状態、用途への適合性を網羅しています。

BioReagent グレードガイドを見る →

Shall we send you a message when we have discounts available?

Remind me later

Thank you! Please check your email inbox to confirm.

Oops! Notifications are disabled.