Determine the necessary mass, volume, or concentration for preparing a solution.
For fungal sterility testing of pharmaceuticals
The following is general, literature-based guidance for preparing and using selective fungal media. It is not specific to this item; consult the CoA/Spec Sheet for exact directions.
• Materials: Dehydrated medium; purified water; sterile bottles; autoclave; optional selective supplements; sterile filters (0.22 µm) for heat-labile agents; Petri dishes. • Preparation:
Item-specific volumes, concentrations, and supplement identities: Not specified for this item; refer to CoA/Spec Sheet.
This product is not a single biomolecule but a nutrient matrix designed to support or select for specific microorganisms.
Literature/general functional roles of components in modified Martin-type selective media: • Carbon/energy sources: Carbohydrates (e.g., simple sugars or polysaccharides) support fungal primary metabolism, sporulation, and hyphal extension. • Nitrogen sources: Peptones/yeast derivatives supply amino acids, peptides, vitamins, and trace growth factors essential for many filamentous fungi and oomycetes. • Mineral balance and buffering: Inorganic salts maintain osmotic balance and provide cofactors (e.g., K+, Mg2+, PO43−) important for enzymatic activity. • Selective agents: Dyes and/or antibiotics restrict bacterial proliferation and, in some formulations, limit rapid-spreading mycelia to facilitate colony isolation. These agents modulate membrane integrity, translation, or nucleic acid processes in non-target organisms. • Gelling agent (when agar-based): Provides a semi-solid matrix for colonial morphology, sporulation structures, and isolation streaking.
Item-specific composition and target organism spectrum are Not specified for this item; refer to CoA/Spec Sheet. Users should validate growth/selectivity with relevant control strains.
This product is a complete/selective culture medium rather than a dedicated buffering reagent. It is not typically used to prepare defined buffer systems for biochemical assays.
• Practical note: Many culture media contain inherent buffering capacity from phosphates or organic components, which stabilizes pH during incubation. However, if a defined buffer is required for enzymology or extraction, use a dedicated buffering system (e.g., phosphate, citrate, Tris) prepared separately. • Item-specific buffer properties (pH targets, capacity): Not specified for this item; refer to CoA/Spec Sheet.
While culture media inherently rely on water as a green solvent, sustainability considerations focus on preparation efficiency, waste minimization, and energy use.
• Greener practices (general):
No therapeutic claims. This product is intended for research use only (from Product Data: For research use only).
General/literature context in pharmaceutical and industrial microbiology: • Environmental monitoring and bioburden testing: Selective fungal media are often incorporated into environmental surveillance workflows to detect and enumerate molds/yeasts from air, surfaces, and raw materials. • Raw material/microbial limit tests: May be used, where appropriate and validated, to recover objectionable fungi from non-sterile products. • Process hygiene studies: Useful for isolating environmental isolates for identification and trend analysis.
Item-specific pharmacopeial status, compliance (e.g., USP/EP), and validated methods: Not specified for this item; refer to CoA/Spec Sheet and your quality unit before use in GMP settings.
Item-specific physical parameters are not provided in the Product Data. See below for general, literature-based characteristics of dehydrated culture media; these are not specifications for this item.
• Physical state (item): Dehydrated powdered medium (appearance: Not specified for this item; refer to CoA/Spec Sheet.). • Solubility (literature/general): Designed to be water-soluble; dissolves in purified/deionized water with heating and stirring. • pH of prepared medium (literature/general): Selective fungal media are often adjusted to mildly acidic pH; exact pH target for this item is Not specified for this item; refer to CoA/Spec Sheet. • Osmolality/ionic strength (literature/general): Determined by salts and peptone/carbohydrate content; not specified for this item. • Melting/boiling points, density, refractive index: Not applicable/not specified for this item; refer to CoA/Spec Sheet. • Color/clarity (literature/general): Prepared medium may be translucent to slightly opalescent; color depends on included dyes/antibiotics; item-specific appearance is not specified. • Typical preparation concentration (literature/general): Manufacturer-defined; Not specified for this item; refer to CoA/Spec Sheet.
• Supplied grade: BioReagent (from Product Data). In Aladdin’s catalog, BioReagent-grade products are suitable for laboratory research workflows, including microbiology and cell-based assays, where consistent performance and low bioburden are important. • What this implies (general):
This product is used for microbiological culture, not chemical synthesis. The term “applications” here refers to microbiological workflows.
Literature/general applications of Modified Martin-type media: • Selective isolation: Frequently employed to isolate filamentous fungi and certain oomycetes from soil, plant, water, and environmental samples by suppressing fast-growing bacteria via selective agents. • Enumeration and diversity studies: Useful for CFU counts, recovery of slow-growing colonies, and morphological observation under selective pressure. • Plant pathology and environmental microbiology: Employed in baiting and recovery protocols from plant tissues, rhizosphere soil, or irrigation water. • Method development: Tuning selectivity by adjusting supplements (e.g., antibiotics, dyes) and incubation temperature to favor target taxa while minimizing contaminants. • Teaching/QA labs: Demonstrates principles of selective/differential media and recovery from complex matrices.
Item-specific validated organisms and supplements are Not specified for this item; refer to CoA/Spec Sheet. Users should confirm suitability with control strains and local sample types and, if needed, adjust supplement panels according to the intended targets.
Chemical reaction conditions do not apply. Instead, below are general, literature-based preparation and handling conditions for dehydrated selective media. These are guidelines only and are not specifications for this item.
• Reconstitution: Disperse the manufacturer-recommended mass of powder in purified water with stirring. Heat to near boiling to fully dissolve; avoid scorching. • Sterilization: Autoclave at 121°C for 15 minutes (standard gravity or pre-vacuum cycles as validated). For heat-labile selective agents, sterilize the base medium only; cool to ~45–55°C and aseptically add filter-sterilized supplements. • Plating: Pour into sterile plates at ~45–50°C to a uniform depth (commonly ~20–25 mL for 90-mm plates; adjust per protocol). Allow to solidify on a level surface and dry plates as needed to remove surface moisture. • Incubation (selective fungal recovery, literature/general): 20–30°C is typical for many environmental fungi/oomycetes; exact temperature/time depend on target organisms and regulatory method. • Quality checks: Include uninoculated sterility controls and positive-control strains to confirm growth promotion and selectivity each lot/batch.
Item-specific preparation concentration, target pH after sterilization, and supplement list: Not specified for this item; refer to CoA/Spec Sheet.
• GHS/Classification: Not specified for this item; refer to SDS for authoritative hazard and precautionary statements. • Common laboratory precautions (general):
This product is a culture medium; the relevant solvent is purified water.
• Primary solvent: Water of appropriate quality for microbiological media preparation (e.g., Type II or better; low TOC; free of inhibitory residual disinfectants). • Compatibility (general): Fully water-soluble upon heating and stirring. Avoid hard/untreated tap water due to variable ions/chloramines that can inhibit growth or precipitate components. • Practical guidance:
• Storage (from Product Data): Room temperature. Keep container tightly closed in a dry place. Protect from humidity to prevent clumping/degradation. • Shipping (from Product Data): Shipped under normal conditions. • Shelf life: Not specified for this item; refer to CoA/Spec Sheet. Inspect for caking, discoloration, or odor before use. • Reconstitution (general guidance): Dissolve the manufacturer-recommended mass in purified water with stirring and heat until fully dissolved. Target pH, concentration, and any required supplements are Not specified for this item; refer to CoA/Spec Sheet. • Sterilization (general): Autoclave base medium at 121°C for 15 min unless otherwise stated. Add heat-labile selective agents via sterile filtration after cooling to ~45–55°C, with aseptic technique. • Prepared media storage (general): Store sealed plates or bottled broth at 2–8°C, protected from light if dye-containing. Allow plates to equilibrate to room temperature and dry condensation before use. Typical in-lab shelf life for many prepared selective media is on the order of weeks; exact stability for this item is Not specified for this item; refer to CoA/Spec Sheet. • Freeze–thaw: Not applicable for dehydrated powder. Avoid freezing prepared agar plates to prevent cracking and loss of performance.
• Product type: Dehydrated microbiological culture medium (complex mixture), not a single defined compound. • SKU: M1528261; Product Name: Modified Martin Medium; Grade: BioReagent (from Product Data). • Chemical identifiers (molecular formula, MW, SMILES, InChIKey, CAS, CID): Not specified for this item; refer to CoA/Spec Sheet. • Structural features: Not applicable to a complex medium. This product comprises multiple organic/inorganic components blended as a powdered medium. • 2D/functional description (literature/general): Modified Martin media are commonly formulated as selective media intended to favor growth of filamentous fungi and/or oomycetes while suppressing fast-growing bacteria. Selectivity is typically achieved by inclusion of specific inhibitors (e.g., dyes and/or antibiotics) alongside nutrient sources (carbon, nitrogen, minerals) and, when supplied as agar, a gelling agent. Exact composition and proportions vary by manufacturer and formulation and are not specified here.
Not a synthetic organic reagent. As a microbiological medium, it has no direct role in chemical synthesis.
Related, literature-based utility in bioprocess and biocatalysis: • Strain maintenance: Selective recovery of environmental fungal/oomycete strains that may later serve as sources of enzymes, secondary metabolites, or biocatalysts. • Pre-screening: Isolation plates for obtaining axenic colonies prior to fermentation optimization or metabolite discovery workflows. • Phenotypic assays: Supports morphological and growth-rate comparisons under selective pressure to infer resistance/tolerance traits.
Item-specific composition enabling any specialized synthetic application is Not specified for this item; refer to CoA/Spec Sheet.
No antibody or molecular targeting information applies. For selective media, “specificity” refers to microbial selectivity, not molecular binding.
• Literature/general note: Modified Martin-type media are typically designed to favor recovery of filamentous fungi and/or oomycetes while suppressing bacterial contaminants using dyes and/or antibiotics. The precise spectrum (which taxa are favored or inhibited) depends on the exact formulation and supplement panel. • Item-specific target organisms and inhibitory spectrum: Not specified for this item; refer to CoA/Spec Sheet and validate with control organisms relevant to your workflow.
当社のグレード選定ガイドでは、カタログ内のすべてのバリエーションについて、純度、安定剤の状態、用途への適合性を網羅しています。
BioReagent グレードガイドを見る →