Phenoxyacetylcellulose , CAS No.68332-77-4

CAS: 68332-77-4 Cat. No.: P121046
注文可能
Storage
Room temperature
Shipped In
Normal
★
サイズ
USA
ドイツ (EU)*
価格
個数
1g
P121046-1g
受注生産 · 8~12週間

$205.90

$241.90
保存 $36.00 (14.88%)
5g
P121046-5g
受注生産 · 8~12週間

$585.90

$684.90
保存 $99.00 (14.45%)
Enter a quantity for the sizes you want to add.

概要

A support for the immobilization of enzymes and other proteins by hydrophobic adsorption.

仕様

保管条件
Room temperature
入荷
Normal
名前と識別子
WGKドイツ
3

詳細データ

証明書(CoA、COO、BSE/TSEと分析図)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:
ソリューション計算機
レビュー

顧客レビュー

Application Protocols

Not item-validated.

  • No manufacturer-tested biological application protocols (e.g., WB, IHC, IF, FC) are provided for this chemical reagent.

General lab protocols (literature-based; for materials processing)

  • Solution preparation: Dry polymer (50–60 °C under vacuum, 12–24 h). Dissolve 5 wt% in acetone/DMF (80/20) with stirring 12 h. Filter 0.2 µm PES. Use immediately.
  • Spin coating (example): 2000 rpm, 60 s on cleaned substrate; soft bake 60 °C, 10 min; hard bake 90–110 °C, 30 min (below degradation onset). Adjust concentration/spin speed to target thickness.
  • Membrane casting (example): 15 wt% in DMAc; degas; cast with 200 µm knife; immediate immersion into water bath at 20 °C; rinse 24 h with frequent water changes; store wet or dry under restraint to minimize curl.

These are illustrative literature-style procedures and require optimization for your specific lot and equipment.

Biological Roles

Context (general knowledge)

  • Cellulose is a naturally occurring structural polysaccharide of plant cell walls. In phenoxyacetylcellulose, the hydroxyl groups are esterified, substantially altering hydrogen-bonding, hydrophilicity, and biodegradation relative to native cellulose.
  • Biological activity: As a chemically modified cellulose, phenoxyacetylcellulose is not known to exhibit intrinsic, specific biological signaling or enzymatic activity. Enzymatic degradation by cellulases/esterases is expected to be markedly reduced versus native cellulose and will depend on degree of substitution and accessibility.
  • Biomaterials perspective: The aromatic ester substitution typically reduces water uptake and protein adsorption compared to unmodified cellulose. Films and membranes can serve as inert supports for in vitro assays, separations, and controlled diffusion studies.

Use in life-science workflows

  • Matrix/support: Can be used to prepare solid supports, coatings, or membranes for analytical separations or immobilization after additional surface functionalization.
  • Biocompatibility: Literature suggests many cellulose derivatives exhibit favorable cytocompatibility as materials; however, performance is formulation- and process-dependent. No item-specific biocompatibility data are provided—evaluate empirically for your system.

Note

  • For research use only (per Product Data). No medical, clinical, or in vivo claims are made or implied.
Buffer Applications

Not typically applicable.

  • Phenoxyacetylcellulose is an organic polymer solid and is not used as a buffer component. It does not provide acid/base conjugate pairs suitable for pH control in aqueous systems.
  • For relevant information, see Solvent Selection (for preparing polymer solutions) and Reaction & Applications (for films, membranes, and supports).
Green Alternatives

Perspective (general/green chemistry considerations)

  • Renewable backbone: Cellulose-based polymers already leverage a renewable, bio-based backbone. Environmental footprint largely depends on derivatization chemistry and solvent choices during processing.

Greener processing options

  • Prefer bio-derived or lower-toxicity solvents where solubility allows: 2-methyltetrahydrofuran (2-MeTHF) over THF; ethyl acetate or acetone over chlorinated solvents; Cyrene or dimethyl carbonate (DMC) are emerging options—screen for solubility and film quality.
  • Solvent recovery: Implement closed-loop solvent capture/condensation and distillation to minimize VOC emissions.
  • Aqueous coagulation: For membrane formation, use water or aqueous alcohols as non-solvents to avoid chlorinated baths.
  • Energy efficiency: Dissolve at the lowest temperature consistent with reasonable kinetics; use high-shear mixing to reduce heat demand.

Comparison (literature; qualitative)

  • Chlorinated solvents (DCM/CHCl3): Excellent solubility/fast drying but poor EHS profile; aim to replace with acetone/ethyl acetate where feasible.
  • Polar aprotics (DMF/DMAc/NMP): Strong solvents but reproductive toxicity concerns; consider mixtures with acetone/MEK to reduce usage, or evaluate safer alternatives (e.g., propylene carbonate, Cyrene) if compatible.

Trade-offs

  • Greener solvents may slow drying, alter morphology, or reduce gloss. Validate mechanical and optical targets under adjusted drying/annealing protocols.
Pharmaceutical Uses

General formulation context (no therapeutic claims)

  • Cellulose derivatives are widely used as excipients (binders, film formers, coatings). Aromatic acyl cellulose esters like phenoxyacetylcellulose are less common in registered pharmacopeial monographs than aliphatic esters (e.g., cellulose acetate, cellulose acetate phthalate).
  • Potential roles under research/industrial evaluation: specialty film coatings for tablets or devices, barrier layers with improved solvent resistance, or matrix formers in experimental controlled-release systems. Suitability depends on regulatory status, extractables/leachables profile, and residual solvent content.

Regulatory/status notes

  • Pharmacopeial listing: Not specified for this item; refer to CoA/Spec Sheet and applicable pharmacopeial references.
  • Residual solvents, heavy metals, bioburden/endotoxin: Not specified for this item; would require lot-specific testing for pharmaceutical development.

Practical guidance

  • If considering use in preclinical formulation research, conduct full compatibility screening with actives and plasticizers, evaluate film integrity, and assess extractables under ICH Q3C/Q3D frameworks. This product is for research use only (per Product Data).
Physical Properties

Item-specific (from Product Data)

  • Appearance: Not specified for this item; refer to CoA/Spec Sheet.

Literature/general expectations for cellulose arylacyl esters (not item specifications)

  • Physical state: Typically off-white to light tan amorphous solid or powder; film-forming.
  • Thermal behavior: Glass transition temperature (Tg) often in the 120–200 °C range depending on DS and molecular weight; onset of thermal decomposition typically >200 °C under nitrogen. Exact values for this item are not specified.
  • Solubility profile: Usually insoluble in water; soluble to varying degrees in polar aprotic and chlorinated organic solvents (e.g., acetone, THF, 1,4-dioxane, CHCl3, CH2Cl2, DMF, DMAc). Solubility is strongly DS- and Mw-dependent.
  • Density: Commonly ~1.2–1.4 g/cm³ for cellulose esters (literature); item-specific value not specified.
  • Refractive index: Not typically reported for powders; films may show n ≈ 1.47–1.52 (literature), DS-dependent.
  • pKa/logP: Not applicable in the usual sense for macromolecular non-electrolyte esters; bulk hydrophobicity increases with DS.

Important

  • Do not treat the above as product specifications. For batch-specific data (DS, Mn/Mw, solubility screening, Tg, ash content, residual solvents), consult the item’s CoA/Spec Sheet.
Quality and Grades

Item-specific (from Product Data)

  • Grade/purity: Not specified for this item; refer to CoA/Spec Sheet.

Guidance on quality attributes for polymeric cellulose esters (general knowledge)

  • Degree of substitution (DS): Central quality parameter controlling solubility, film strength, and chiral recognition propensity; reported as average substituents per anhydroglucose unit. Batch-specific DS should be provided on the CoA when applicable.
  • Molecular weight distribution: Mn, Mw, and dispersity (Đ) determine solution viscosity and coating behavior; often reported via GPC/SEC in suitable solvents.
  • Residual solvents and volatiles: Important for film/coating applications and analytical uses; typically assessed by GC/TGA.
  • Inorganic content (ash): Impacts optical clarity and dielectric properties in films; low ash is preferred for electronics and optics.
  • Color/clarity: APHA color or yellowness index for film applications; UV absorbance baseline can matter if used in optical devices.
  • Stabilizers/additives: Unless specified, cellulose esters are typically offered without added stabilizers. Any stabilizer or plasticizer content would be declared on the CoA.

Interpretation

  • If you require a defined DS, viscosity grade, or particle size for a specific application (membranes, coatings, chiral stationary phases), contact us for current batch specifications or a custom lot.
Reaction and Applications

Applications (literature/general knowledge; expand as appropriate)

  • Film/coating material: Phenoxyacetylcellulose, as an arylacyl cellulose ester, forms tough, transparent films suitable for optical test films, protective coatings, and dielectric layers. DS and Mw control mechanical modulus and transparency.
  • Membranes: Processable via phase inversion to yield micro- to ultrafiltration membranes. Aromatic content typically enhances solvent resistance and thermal stability relative to aliphatic esters.
  • Chiral recognition research: Cellulose arylcarboxylate/carbamate derivatives are widely studied as chiral selectors. Phenoxyacetyl substitution offers π–π and hydrogen-bond-acceptor interactions that can impart enantiodiscrimination when coated on silica (research literature). Performance is DS- and substituent-pattern dependent.
  • Polymer blends/composites: Acts as a functional, renewable filler or matrix providing stiffness and improved solvent resistance; compatible with certain bio-based plasticizers.
  • Surface modification scaffold: Pendant ester groups can be further transformed (e.g., partial hydrolysis to regenerate hydroxyls) enabling post-functionalization with dyes, ligands, or crosslinkers.

Practical notes

  • Drying and handling: Avoid moisture uptake before dissolution to maintain reproducibility. Use anhydrous solvents and sealed vessels for coating-grade solutions.
  • Degassing: For coating and chromatography applications, degas polymer solutions (vacuum or sonication) to minimize bubbles and defects.
  • Crosslinking/curing: Optional post-treatments (thermal annealing below degradation onset) can densify films; chemical crosslinking requires tailored chemistries not intrinsic to this ester.

Item-specific application claims are not provided; consult the CoA or contact us for batch data (DS, viscosity) to match your use case.

Reaction Conditions

Processing and modification conditions (literature; general guidance)

  • Dissolution: 1–10 wt% in acetone, THF, DCM, CHCl3, DMF, or DMAc at 20–50 °C with stirring; warm gently to accelerate dissolution. Filter (0.2–0.45 µm) before coating.
  • Film casting: Cast at 20–30 °C, controlled RH (30–50%). Dry under ambient or mild vacuum. Post-anneal 60–120 °C (below Tg and well below decomposition) to densify films.
  • Phase inversion membranes: Prepare 10–25 wt% dope in DMAc/DMF; degas; cast and immediately immerse in water or aqueous alcohol coagulant. Tune pore structure by solvent/non-solvent ratio, temperature, and polymer concentration.
  • Partial hydrolysis: Basic or acidic conditions (e.g., NaOMe/MeOH or dilute HCl in an alcohol/THF mixture) at ambient to 40 °C can cleave phenoxyacetyl esters; monitor to avoid backbone degradation. Quench and thoroughly wash.
  • Grafting/post-functionalization: Carbamate formation using isocyanates at 0–25 °C in anhydrous solvents can functionalize regenerated hydroxyls; use catalytic base (e.g., DMAP) where compatible.

Analytics

  • Monitor transformations by FTIR (ester C=O ~1730 cm⁻¹), 13C CP/MAS NMR, and solution NMR if fully soluble. Assess Mw retention by GPC in suitable solvent (e.g., CHCl3/THF) with multi-angle light scattering.

Caution

  • Values above are typical literature practices, not product specifications. Optimize to your polymer lot (DS/Mw unknown for this item).
Safety and Handling

Item-specific (from Product Data)

  • GHS classification, signal word, pictograms, H-statements: Not specified for this item; refer to SDS.
  • Storage: Room temperature; ship under normal conditions.

General safety guidance for cellulose esters (literature/general knowledge)

  • Expected hazards: Low acute toxicity; treat as a combustible organic solid and a nuisance dust. Finely divided powders may form dust clouds—avoid dust generation and ignition sources.
  • PPE: Wear safety glasses with side shields, lab coat, and suitable gloves (e.g., nitrile). Use a dust mask or respirator if dusts/aerosols may be generated. Handle in a fume hood during dissolution in volatile organic solvents.
  • Incompatibilities: Strong oxidizers, strong acids/bases (which can catalyze hydrolysis), and open flames/heat sources. Avoid prolonged exposure to moisture and high temperature to limit hydrolysis of ester groups.
  • Thermal decomposition: Heating above decomposition may release CO/CO2 and aromatic-containing vapors; ensure adequate ventilation.
  • First aid (overview; defer to SDS): If inhaled—move to fresh air; seek medical attention if symptoms persist. Skin/eye contact—wash with water for 15 minutes; remove contaminated clothing. Ingestion—rinse mouth; seek medical advice.
  • Spill response: Avoid dust, sweep up gently, place in suitable container. For solutions, absorb with inert material; dispose per local regulations.

Always consult the official SDS for authoritative hazard classifications and response procedures.

Solvent Selection

General guidance (literature; not item specifications)

  • Polarity class: Weakly to moderately polar, aprotic-polymer compatible; hydrophobic due to arylacyl substituents.
  • Likely good solvents: Acetone, 1,4-dioxane, tetrahydrofuran (THF), methyl ethyl ketone (MEK), dichloromethane (DCM), chloroform, N,N-dimethylformamide (DMF), N,N-dimethylacetamide (DMAc). Exact solubility depends strongly on DS and Mw.
  • Limited/poor solvents: Water, lower alcohols (MeOH, EtOH) often only swell; aliphatic hydrocarbons generally poor.
  • Miscibility considerations: For film casting, binary solvent systems (e.g., acetone/DMF, THF/DCM) can tune evaporation rate and morphology.

Selection tips

  • Rapid-dry coatings: THF, acetone, or DCM provide fast evaporation but increase risk of skinning and porosity—use controlled humidity.
  • Dense, transparent films: DMF or DMAc (optionally mixed with acetone/THF) slow drying and favor chain relaxation and clarity.
  • Membrane formation (phase inversion): Use DMAc/DMF as solvents and a non-solvent coagulation bath (e.g., water/alcohols) to create asymmetric porosity; optimize with dope concentration and temperature.
  • Solution prep: Dry polymer and solvent to minimize hydrolysis; stir 4–24 h at ambient to 50 °C. Gentle warming aids dissolution; avoid >80 °C to limit degradation.

Note

  • Test a small solubility screen with your specific lot. For chromatographic coating or electronics, use anhydrous, low-residue solvents and 0.2 µm filtration before casting.
Storage and Reconstitution

Item-specific (from Product Data)

  • Storage conditions: Room temperature.
  • Shipped in: Normal conditions.

General guidance for cellulose ester polymers (literature/general knowledge)

  • Container: Keep tightly closed in a clean, dry, inert container. Reseal promptly after opening to limit moisture uptake and contamination.
  • Environment: Store in a cool, dry place away from direct sunlight and sources of heat or ignition. Avoid prolonged exposure to humidity to minimize hydrolysis and caking.
  • Shelf life: Stable for ≥24 months under dry, ambient conditions is typical for cellulose esters; confirm with CoA or requalify by FTIR/viscosity before critical use.
  • Reconstitution/preparation: For solution use, dry the polymer under vacuum (e.g., 50–60 °C, 12–24 h) and use anhydrous solvents. Add polymer gradually to stirred solvent to avoid agglomeration. Allow sufficient time for complete dissolution; slight warming may be applied.
  • Freeze–thaw: Not applicable to the solid; avoid freezing/thawing of prepared solutions as precipitation or gelation can occur. Prepare fresh solutions as needed or store solutions at ambient in sealed containers for the minimum necessary time.

Always refer to the product’s CoA and SDS for batch-specific recommendations.

Structure and Identity

Item-specific (from Product Data)

  • SKU: P121046
  • Product name: Phenoxyacetylcellulose
  • CAS: 68332-77-4
  • Storage: Room temperature; shipped under normal conditions
  • Molecular formula: Not specified for this item; refer to CoA/Spec Sheet.
  • Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.
  • SMILES: Not specified for this item; refer to CoA/Spec Sheet.
  • InChIKey: Not specified for this item; refer to CoA/Spec Sheet.

General structural description (literature/general knowledge)

  • Phenoxyacetylcellulose is a cellulose ester in which some or all of the hydroxyl groups on the β-1→4-linked D-glucopyranose backbone are esterified with phenoxyacetyl (Ph–O–CH2–CO–) groups.
  • Key structural features: polysaccharide backbone (anomeric β-1,4 linkages), multiple secondary ester linkages, pendant aryl-oxyacetyl substituents introducing aromatic rings and ether/ester functionalities.
  • Degree of substitution (DS): Typically variable (0 < DS ≤ 3 per anhydroglucose unit); exact DS for this catalog item is not specified and governs solubility, Tg, and film properties.
  • 2D description in words: A repeating anhydroglucose ring (six-membered pyranose) bearing three positions (C2, C3, C6) that may carry phenoxyacetyl ester groups consisting of an acyl (–CO–CH2–O–Ph) moiety where the benzene ring connects through an ether to the methylene of the acyl chain.

Notes

  • Being a polymer/oligomeric material, exact elemental formula, average molecular weight (Mn/Mw), and dispersity depend on synthesis and are batch-specific.
Synthetic Utility

General synthetic value (literature/general knowledge)

  • Functional polymer scaffold: The cellulose backbone offers a high-density array of pendant ester groups. While phenoxyacetyl esters are relatively stable, controlled partial hydrolysis can regenerate hydroxyls for further derivatization (e.g., carbamate formation, etherification, or grafting).
  • Support for separations: Coating of silica or monolithic supports with cellulose arylacyl derivatives is a known route to prepare chiral stationary phases (CSPs) in analytical research. Phenoxyacetyl substitution provides aromatic and ether functionalities that can engage in π–π and dipolar interactions with analytes.
  • Film and membrane fabrication: From a synthetic processing standpoint, the polymer enables casting, spin-coating, and phase inversion to generate tailored microstructures serving as substrates for subsequent chemical modification or device integration.
  • Composites and coatings: Acts as a renewable matrix compatible with nanoparticles, dyes, and crosslinkers to build functional materials (optical filters, barrier coatings). Post-functionalization at residual hydroxyls or via transesterification strategies can introduce active sites.

Notes

  • Reaction chemistry on the polymer should consider diffusion limits and preservation of backbone integrity. Monitor by FTIR, solid-state NMR, and GPC to confirm substitution changes and avoid chain scission.
  • Item-specific DS/Mw are not provided; reaction planning should include a small-scale titration to determine reactivity and solubility.
Target Specificity

Not applicable.

  • This product is a polymeric chemical reagent, not a biological affinity reagent. No antigen/epitope, species reactivity, clone, or isotype information is relevant or provided.

Shall we send you a message when we have discounts available?

Remind me later

Thank you! Please check your email inbox to confirm.

Oops! Notifications are disabled.