Determine the necessary mass, volume, or concentration for preparing a solution.
Dilution Calculator
Determine the dilution needed to prepare a stock solution.
Reconstitution Calculator
Recensioni
Recensioni dei clienti
Application Protocols
No assay-specific protocols (e.g., WB, IHC, IF, FC) apply. The following is a general procedure for conductivity calibration using an aqueous KCl standard (literature/general). Use the item’s CoA/Spec Sheet for certified values.
Preparation
Equilibrate the standard, probe, and calibration beaker to the target temperature (ideally 25.0 °C).
Rinse the conductivity probe with Type I water, then with a small aliquot of the standard.
Single-point calibration
Pour a fresh portion of the KCl standard into a clean beaker.
Insert the probe; gently stir or use a stir bar to maintain uniformity.
Wait for the reading to stabilize; set the instrument to the certified value at the measured temperature (from the CoA temperature table).
Multi-point calibration (if required)
Repeat with additional standards spanning the measurement range. Do not mix standards; rinse thoroughly between points.
Post-calibration verification
Check a second standard or a known sample to confirm accuracy.
Good practices
Do not return used aliquots to the bottle.
Cap immediately after use to limit evaporation/contamination.
Record lot number, temperature, and instrument ID.
These steps are generic; adjust to your instrument’s manual and the lot-specific CoA.
Biological Roles
While this product is intended for analytical calibration and not for biological experimentation, understanding the ions involved provides useful context.
Potassium (K+) (literature/general)
Major intracellular cation in living cells; critical for membrane potential maintenance, enzyme activation, and osmoregulation.
Transported via potassium channels and pumps; participates in action potentials and cellular excitability.
Chloride (Cl−) (literature/general)
Principal extracellular anion; contributes to osmotic balance and acid–base homeostasis.
Transmembrane movement via GABA_A receptor channels, ClC transporters, and other anion channels.
Relevance to conductivity measurements (general)
KCl fully dissociates in water to yield mobile ions, making it an ideal, predictable electrolyte for conductivity calibration across a broad concentration range.
Temperature dependence of ion mobility underlies the need to calibrate at defined temperatures (often 25 °C) or apply ATC.
Important caveats
This product is labeled for research use only and intended for analytical calibration. It is not formulated for cell culture, in vivo use, or clinical applications.
Any biological use would require verification of bioburden, endotoxin, and trace metal content—none of which are specified for this item.
For biochemical assays requiring ionic strength adjustment, prepare fresh KCl solutions from reagent-grade solids to known concentrations, unless the product’s CoA explicitly supports such use.
Buffer Applications
This product is not a buffer and is not primarily intended for buffering applications. It is an aqueous KCl electrolyte used for conductivity calibration.
General notes (literature/general)
KCl solutions provide ionic strength but have negligible buffering capacity because KCl does not participate in acid–base equilibria in water.
If you require a buffer at defined pH with known conductivity, prepare a buffer (e.g., phosphate, Tris, HEPES) and, if needed, adjust ionic strength by adding a known amount of KCl prepared separately.
Item-specific buffer-relevant details
pH, buffering range, and composition: Not applicable/not specified for this item; refer to CoA/Spec Sheet if any such details are provided for compatibility information.
For electrophoresis, chromatography, or enzymology where pH control is essential, use appropriate buffer systems and reserve this KCl standard for instrument calibration only.
Green Alternatives
Aqueous KCl conductivity standards are already among the greener calibration media because they are water-based, nonflammable, and typically low in hazard. That said, sustainability and safety can still be optimized.
Environmental and safety profile (general)
Water solvent matrix, no VOCs.
Typically low toxicity; chloride and potassium are common ions in natural waters. Dispose according to local regulations to avoid unnecessary salinization.
Possible alternatives/complements (literature/general)
NaCl standards: Similar green profile; may be preferred in workflows standardized on sodium chloride correlations for TDS.
KNO3 standards: Chloride-free environments (where Ag+ or other chloride-reactive species are present) may benefit from nitrate-based electrolytes.
Packaging and use recommendations
Select bottle sizes that match usage rates to reduce waste and contamination risk.
Refillable glass or recyclable HDPE packaging can reduce environmental footprint; verify compatibility with your QA procedures.
Use reusable, dedicated calibration beakers; avoid single-use plastics where practical.
Comparison highlights (literature/general; not item-specific):
Matrix: All are water-based; hazard is low relative to organic calibration media.
Interference: KCl introduces Cl−; avoid in systems sensitive to chloride (e.g., Ag/AgCl precipitation). KNO3 avoids chloride but introduces NO3−.
Traceability: Available for all three; choose based on instrument method and existing SOPs.
The greenest approach is accurate sizing, careful handling to extend shelf life, and proper disposal.
Pharmaceutical Uses
No pharmaceutical or clinical use is intended or claimed for this product. It is supplied for research and analytical calibration only.
Excipient/formulation role (general context)
Aqueous KCl can serve as an isotonicity or electrolyte component in some pharmaceutical contexts, but such applications demand compendial grade materials, validated water systems, and strict microbial/endotoxin controls.
Item-specific status
Pharmacopeial compliance (e.g., USP/EP), endotoxin/bioburden limits, and excipient suitability: Not specified for this item; refer to CoA/Spec Sheet.
Appropriate use case here
Calibration and verification of conductivity instrumentation in development or QC laboratories, provided the lot’s documentation meets your internal SOPs.
Do not use this product for human or veterinary applications. For any GMP-relevant work, procure appropriately qualified materials with full regulatory documentation.
Physical Properties
Item-specific physicochemical specifications are not provided for this product. For any required numeric specifications (e.g., KCl concentration, conductivity value at 25 °C, density), see the product’s CoA/Spec Sheet.
Item-specific values
Concentration: Not specified for this item; refer to CoA/Spec Sheet.
Conductivity at 25 °C: Not specified for this item; refer to CoA/Spec Sheet.
pH: Not specified for this item; refer to CoA/Spec Sheet.
Density/refractive index: Not specified for this item; refer to CoA/Spec Sheet.
Literature/general reference values for KCl in water (examples, not item specifications)
0.001 M KCl ≈ 147 µS·cm−1 at 25 °C (literature)
0.01 M KCl ≈ 1413 µS·cm−1 at 25 °C (literature)
0.1 M KCl ≈ 12.88 mS·cm−1 at 25 °C (literature)
1.0 M KCl ≈ 111.3 mS·cm−1 at 25 °C (literature)
Temperature coefficient: Conductivity typically increases ~2% per °C near room temperature; exact value depends on concentration (literature).
Appearance (general expectation)
Clear, colorless aqueous solution when uncontaminated (literature/general). Actual appearance for this item: Not specified; refer to CoA/Spec Sheet.
Solubility (literature)
KCl is highly soluble in water; in solution it exists as dissociated K+ and Cl− ions. Non-miscible with nonpolar solvents.
Note: Use only the item’s CoA/Spec Sheet values for calibration; the literature values above are examples to provide context.
Quality and Grades
Item-specific grade/purity
Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.
What “conductivity standard” typically implies (literature/general)
Prepared from high-purity KCl and Type I water with tight control of concentration and temperature normalization to 25 °C.
Traceable standards may reference national metrology institutes with stated uncertainty (e.g., ±0.5–1.0% at 25 °C), and may include a lot-specific certificate with temperature-conductivity tables.
Low total organic carbon (TOC) and low ionic contaminants to minimize drift and ensure reproducibility.
UV absorbance/metal specifications
Not specified for this item; refer to CoA/Spec Sheet. Do not assume organic purity or metal content beyond what is documented.
Stabilizers/preservatives
Not specified for this item; refer to CoA/Spec Sheet. Some conductivity standards include biocide to resist microbial growth; presence/absence should be confirmed on the lot CoA.
Practical quality controls for users
Verify labeled conductivity against a secondary standard or freshly prepared reference at 25.0 ± 0.1 °C.
Record lot number, opening date, and storage history; replace solutions that show turbidity, microbial growth, or labeling damage.
Avoid evaporative concentration by keeping containers tightly closed and minimizing headspace exposure during use.
For regulated calibrations, rely on the item’s lot-specific CoA/Spec Sheet for traceability, uncertainty, and use-by date.
Reaction and Applications
Primary application: calibration and verification of electrolytic conductivity measurements. Concentration and nominal conductivity for this specific item are not specified; consult the CoA/Spec Sheet for lot-certified values.
Core uses (laboratory/instrumentation)
Single- or multi-point calibration of benchtop and portable conductivity/TDS meters.
Determination and verification of a conductivity probe’s cell constant (K) across measurement ranges.
Instrument performance qualification (IQ/OQ/PQ) in QA/QC laboratories.
As an inert supporting electrolyte (KCl) in aqueous electrochemistry where chloride is compatible (e.g., some voltammetric studies). Note: If using this product for electrochemistry, verify concentration and contaminants via CoA; standards may contain preservatives that impact electrochemical backgrounds.
Practical technique notes
Temperature control: Conductivity is temperature dependent; calibrations should be performed at known temperature or using ATC with the correct temperature coefficient profile.
Cleanliness: Use clean, dedicated glassware; avoid metal contamination (Ag+, Pb2+) that can precipitate with Cl− and change ionic content.
Rinsing: Rinse electrodes with Type I water and a small aliquot of standard before immersion for the reading.
Equilibration: Allow the probe signal to stabilize; gently stir to avoid polarization effects at the electrodes.
Documentation
Record lot number, nominal conductivity, temperature, and instrument ID in calibration logs to ensure traceability.
Reaction Conditions
Because this product is intended for conductivity calibration rather than chemical reactions, there are no item-specific reaction conditions. The following guidance pertains to calibration measurements and general electrochemical handling (literature/general):
Temperature control
Calibrate at 25.0 °C where possible, or apply instrument-specific ATC. Document the temperature coefficient used. Conductivity typically varies by ≈2% per °C around room temperature.
Electrode and cell handling
Clean cell with high-purity water; avoid abrasive cleaning that alters the cell constant. For persistent fouling, follow manufacturer cleaning protocols (acid/base rinses as appropriate, then thorough rinsing).
Gently stir during measurement to minimize electrode polarization and boundary layer effects.
Measurement protocol tips
Use fresh aliquots poured into a clean beaker; never return used standard to the stock bottle.
Allow readings to stabilize; accept the value when drift is within instrument specifications.
Perform multi-point calibration if spanning wide ranges (e.g., 84 µS/cm, 1413 µS/cm, 12.88 mS/cm standards; values are literature examples, not specifications for this item).
Expected performance (general)
With a properly maintained probe, readings should agree with the standard’s certified value within the instrument’s stated accuracy and the standard’s uncertainty.
Always defer to your instrument manufacturer’s SOPs and the lot-specific CoA for certified values and temperature tables.
Safety and Handling
Safety information specific to this product (GHS classification, signal word, hazard statements, pictograms) is not provided here. Always consult the product SDS for authoritative guidance.
Item-specific safety data
GHS classification, H-statements, pictograms: Not specified for this item; refer to SDS.
General safety considerations for aqueous KCl solutions (literature/general)
Typically considered low hazard in dilute form; avoid ingestion and eye/skin contact.
May cause eye irritation; rinse cautiously with water for several minutes if contact occurs.
Slippery when spilled—clean promptly to prevent slips.
Handling practices
Use appropriate PPE: lab coat, safety glasses, and nitrile gloves.
Prevent contamination: do not pipette from the stock bottle directly into samples; pour aliquots to minimize back-contamination.
Avoid cross-labeling with other standards—misuse can corrupt calibration data.
Storage incompatibilities (general)
Avoid mixing with strong acids/bases or reactive salts that could alter ionic strength or introduce precipitating ions (e.g., Ag+ forms AgCl).
First-aid overview (general)
Skin contact: Wash with soap and water.
Eye contact: Rinse cautiously with water for several minutes; remove contact lenses if easy; seek medical attention if irritation persists.
Ingestion/inhalation: Rinse mouth; seek medical advice if unwell.
Spill/cleanup
Absorb with inert material, wipe with water, and dispose according to institutional policies.
Defer to the SDS and institutional risk assessments for final safety measures.
Solvent Selection
This product is an aqueous KCl conductivity standard/solution, not a general-purpose solvent. Solvent selection is therefore not typically applicable. However, the following points can help place it among electrolyte media:
Polarity/miscibility (literature/general)
Matrix: Water (high dielectric constant, ε ≈ 78 at 25 °C); fully miscible with water-based systems.
Not miscible with nonpolar organic solvents. Mixing with organics changes conductivity behavior and invalidates calibration.
When to choose aqueous KCl versus alternatives
Choose KCl standards for routine calibration of conductivity/TDS meters and for setting/validating cell constants of conductivity probes.
Alternatives include NaCl- or KNO3-based standards; selection is often instrument-method driven. Do not intermix standards without re-validating cell constants.
Practical tips
Perform calibrations at controlled temperature (preferably 25.0 °C) or use instruments with Automatic Temperature Compensation (ATC); document setpoints.
Rinse probes with high-purity water, then with a small aliquot of the standard before measurement to minimize carryover.
For chromatography or synthetic work, choose appropriate organic solvents detailed elsewhere; this product is intended specifically for conductivity calibration and related aqueous procedures.
Storage and Reconstitution
Item-specific storage
Store at 2–8 °C, protected from light (per product data).
Shipped on wet ice (per product data). Upon receipt, place in a refrigerator (2–8 °C) promptly.
Stability and shelf life
Shelf life, open-bottle lifetime, and allowable excursions: Not specified for this item; refer to CoA/Spec Sheet.
Handling to preserve quality
Keep container tightly closed to prevent evaporation and contamination, which will alter conductivity.
Do not pipette directly from the stock; pour small working aliquots into clean vessels.
If visible turbidity, growth, or precipitate appears, discontinue use and replace the bottle.
Reconstitution
Not applicable—product is supplied ready-to-use as an aqueous solution. Do not dilute unless your SOP specifically requires it and you can document the new value.
Temperature equilibration
Before calibration, allow an aliquot to equilibrate to the measurement temperature (e.g., 25.0 °C) for accurate readings.
Light protection
While KCl itself is photostable, light protection helps limit algal/microbial growth over time, supporting solution integrity.
For critical calibrations, always consult and record the lot-specific conductivity value(s) and temperature table from the CoA/Spec Sheet. Research use only.
Structure and Identity
Brief description: This product is an aqueous potassium chloride (KCl) conductivity standard/solution intended for calibrating electrolytic conductivity measurements. Concentration for this specific item is not specified.
CAS, InChIKey, SMILES: Not specified for this item; refer to CoA/Spec Sheet.
Composition: Aqueous solution containing potassium chloride (exact concentration not specified).
Component structural features (literature/general)
Potassium chloride (KCl): inorganic ionic compound composed of K+ and Cl−.
Molecular formula (KCl): KCl (literature)
Formula weight (KCl): 74.55 g/mol (literature)
Structural description: In water, KCl fully dissociates into solvated K+ and Cl− ions. The solution contains no discrete molecular “structure”; rather, ions are hydrated within the bulk solvent (H2O).
Practical identity notes
Functional class: Conductivity calibration/electrolyte standard solution.
Typical use: Calibration of conductivity meters and determination/verification of cell constants across temperature ranges.
All identity elements not explicitly stated above should be verified against the product’s CoA/Specification Sheet prior to regulated or critical use.
Synthetic Utility
As supplied, this product is an aqueous KCl conductivity standard, not a synthetic reagent per se. Nevertheless, aqueous KCl (literature/general) has roles in laboratory processes:
Electrolyte/supporting salt
Provides ionic strength and conductivity in electrochemical cells, reference electrode bridges (e.g., saturated KCl for Ag/AgCl electrodes), and certain electrophoretic systems.
Increases solution conductivity to reduce IR drop in electro-organic reactions where chloride is compatible.
Phase and extraction effects
“Salting out” with KCl can influence partitioning in aqueous/organic extractions; however, NaCl is more commonly used for this purpose.
Precipitation chemistry
Chloride can induce precipitation with Ag+, Hg2+, Pb2+; this is generally a concern for contamination control more than a desired synthetic transformation.
Cautions for this product’s use beyond calibration
Concentration, preservatives, and impurity profiles are not specified for synthetic use; verify via CoA if repurposing as electrolyte.
Chloride can corrode certain metals or interfere with catalysts; assess compatibility before use.
For deliberate synthetic applications, it is often preferable to prepare fresh aqueous KCl from solid, weighed reagent-grade KCl to the exact molarity required by the procedure.
Target Specificity
Not applicable. This product is a chemical/electrolyte standard rather than a biological targeting reagent. No antigen/epitope, species reactivity, clone, or isotype information applies to this item.
Utilizziamo i cookie per garantire il corretto funzionamento del sito web e, ove consentito, per migliorare la tua esperienza. Puoi gestire le tue preferenze in qualsiasi momento nelle Impostazioni. Per saperne di più, consulta la nostra Cookie Policy.
Desidera che le inviamo un messaggio quando avremo sconti disponibili?
Ricordamelo più tardi
Grazie! Controlli la sua casella di posta per confermare.
Products are supplied to verified businesses, institutions, and qualified professionals for research and development use only. Not for use in humans, animals, diagnosis, or therapy.