Certificati (CoA, COO, BSE/TSE e tabella di analisi)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:
Calcolatori di soluzioni
Molarity Calculator
Determine the necessary mass, volume, or concentration for preparing a solution.
Dilution Calculator
Determine the dilution needed to prepare a stock solution.
Reconstitution Calculator
Recensioni
Recensioni dei clienti
Application Protocols
Item-specific tested applications, recommended volumes/concentrations, and procedural steps are not specified for this product. Refer to the Aladdin Scientific catalog entry and CoA/Spec Sheet for any provided method notes.
Note: For general literature protocols related to hardness titration with EDTA and metallochromic indicators, consult standard analytical chemistry texts or compendial methods. Do not substitute generic instructions for validated procedures appropriate to your laboratory and this specific product.
Biological Roles
This product is a laboratory indicator for water hardness testing and is not intended for biological or clinical use. No biological role is claimed for SKU H196885.
General background (literature; not item-specific)
Metallochromic indicators are synthetic organic dyes designed for metal-binding and color change; they are not endogenous biomolecules and have no known physiological function.
In biochemical analytics, related chelating dyes can be used for spectrophotometric metal assays, but hardness indicators are typically optimized for aqueous titrimetric methods rather than biological matrices.
Practical note
If quantifying Ca2+/Mg2+ in biological fluids, validated clinical or biochemical assays (ion-selective electrodes, spectrophotometric kits, ICP-OES/MS) are preferred. This product is for research use only and not for diagnostic procedures.
Buffer Applications
Relevance
Hard water indicators are commonly used in buffered aqueous media during EDTA titrations. Item-specific buffer guidance is not provided; refer to CoA/Spec Sheet.
Literature context (not item-specific)
A widely used system employs an ammonia/ammonium chloride buffer at pH ~10 to maintain EDTA in its fully deprotonated, strongly chelating form and to stabilize the dye’s color response to Ca2+/Mg2+.
Buffer ionic strength influences complex stability and endpoint sharpness; maintain consistency across samples and standards.
Practical considerations
Prepare fresh buffer with low-metal salts and deionized water to minimize blank hardness.
Verify the indicator’s effective pH window; some dyes or blends may prefer slightly different pH ranges or alternative buffers (e.g., triethanolamine/NaOH in some methods).
Temperature can subtly affect color contrast and stability constants; perform titrations at a consistent ambient temperature when possible.
Note
Exact buffer composition, pH, and volume additions should follow the method validated for the specific indicator supplied under SKU H196885.
Green Alternatives
Context
Hardness titration indicators are used at very low concentrations, so their overall environmental footprint is dominated by solvent choice, buffers, and waste handling rather than dye mass. Item-specific composition for SKU H196885 is not provided.
Greener practice options (general; literature)
Solvent minimization: Prepare the most concentrated stable stock to reduce alcohol use, or dissolve directly in water if solubility permits.
Prefer ethanol or isopropanol over methanol for stock solutions due to lower toxicity, when compatible with the indicator.
Waste reduction: Microtitrations (smaller sample volumes) minimize chemical waste without compromising accuracy.
Buffer management: Use the minimal buffer strength consistent with a sharp endpoint; verify that alternative buffers (e.g., borate for certain indicators) provide equivalent performance before adoption.
Isopropanol stocks: Low acute toxicity, slower evaporation, good dye solubility.
Methanol stocks: Effective solvent but higher toxicity; consider alternatives when feasible.
End-of-life considerations
Capture colored aqueous waste for appropriate treatment; activated carbon can remove many azo dyes prior to sewering where permitted.
Conclusion
Method optimization (reagent scaling, solvent choice, and waste capture) typically yields the most significant green gains in EDTA hardness assays.
Pharmaceutical Uses
This product is a laboratory indicator for water hardness testing and is provided for research use only. No pharmaceutical or clinical application is claimed or supported for SKU H196885.
General information (context only)
While analytical reagents can support pharmaceutical water quality testing (e.g., monitoring utility waters), any such use must follow compendial methods and validated procedures. Selection of indicator, buffers, and titrants must comply with pharmacopeial monographs if applicable.
Compliance note
If this reagent is incorporated into a regulated QC method, document lot-specific characteristics (per CoA), verify suitability with system suitability tests, and maintain change control. Absent item-specific pharmacopeial status, users should treat this as a general research-grade indicator.
Physical Properties
Item-specific properties
Appearance: Not specified for this item; refer to CoA/Spec Sheet.
Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.
Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.
Melting/Boiling point, density, refractive index, UV/Vis characteristics: Not specified for this item; refer to CoA/Spec Sheet.
Literature/typical properties for hard water indicators (for context only; not specific to this item)
Form: Often supplied as a powder (dye or dye/salt blend) or as a ready-to-use solution.
Solubility: Many metallochromic azo indicators are sparingly soluble in water but dissolve in ethanol, methanol, or mixed aqueous-organic solvents; sulfonated derivatives tend to be water-soluble.
Spectral behavior: Display strong visible absorbance with distinct colors for free dye vs. metal-complexed form; pH strongly affects λmax and color.
pH dependence: Effective color transition commonly near alkaline pH (around pH 10) for Ca2+/Mg2+ detection in EDTA titration systems.
Practical implications
Prepare indicator solutions in solvent systems recommended for the specific dye (commonly ethanol or isopropanol plus water) and buffer the titration medium as required (often ammonia/ammonium chloride, pH ~10, literature).
Verify extinction coefficients, λmax, and working concentration from the product-specific documentation, as these parameters vary significantly among dyes and formulations.
Quality and Grades
Item-specific grade/purity
Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.
Analytical reagent (AR) grade indicator dyes are intended for routine analytical titrations where trace impurities and background absorbance must be controlled.
“Indicator grade” or “titration grade” typically signifies screening for color sharpness at the endpoint, low metal contamination that might bias complexometric titrations, and consistent dye strength.
HPLC or spectroscopy grade is less typical for indicators but, when present, implies low UV background and defined spectral characteristics useful for spectrophotometric titrations.
What to look for on the CoA/Spec Sheet
Dye content or assay basis (where applicable), recommended working concentration, and color transition behavior at defined pH/ionic strength.
Residual metal content: Low Ca2+/Mg2+ is desirable for hardness assays to avoid baseline shifts.
Moisture and insoluble matter: Impact solution clarity and the visual endpoint.
Stabilizers and formulation notes
Some indicator solutions include stabilizers or specific solvents (e.g., alcohol/water) to improve shelf life and solubility. If present, stabilizer identity and content should be disclosed on the spec sheet.
Conclusion
For critical analytical work, rely on the provided CoA lot data for acceptance criteria and replicate performance in your titration method validation.
Reaction and Applications
Primary analytical application (literature; not item-specific)
Complexometric titration of water hardness (Ca2+ and Mg2+) with EDTA. Metallochromic indicators form a colored complex with Mg2+/Ca2+; at the endpoint, EDTA outcompetes the dye for the metal, yielding a distinct color change (e.g., wine-red to blue in the classic Eriochrome Black T system at pH ~10).
Mechanistic notes
The indicator functions as a chelating ligand with colorimetric properties modulated by metal binding and pH.
A buffer (commonly ammonium chloride/ammonia) maintains the pH for sharp endpoints and consistent conditional stability constants.
Typical use cases
Total hardness determination in municipal, industrial, and environmental water testing.
Process control where Ca/Mg concentrations affect scaling, detergency, or water treatment.
Practical tips (general)
Ensure low background metal contamination: use deionized water, clean glassware, and low-metal salts.
Pre-titrate blank to correct for baseline color or any trace metals introduced by reagents.
If Mg2+ is low, some methods add a small, known Mg-EDTA complex to sharpen the Ca endpoint (literature practice); account for it in calculations.
Avoid excess indicator: use only the amount needed for a crisp color change; too much dye can broaden the endpoint.
Note: The exact color transition, optimal pH, and working concentration depend on the specific indicator formulation. Consult the CoA/Spec Sheet for SKU H196885 for definitive directions.
Reaction Conditions
Analytical conditions for EDTA hardness titration (literature guidance; not specific to this item)
Analyte: Ca2+ and Mg2+ (total hardness) in aqueous samples.
Titrant: Standardized EDTA solution (e.g., 0.01 M), standardized against CaCO3 or a primary standard such as CaCO3-derived Ca2+ solution.
pH control: Buffer to pH ~10 using ammonia/ammonium chloride; maintain constant ionic strength.
Indicator: Metallochromic dye solution added in small volume (drops). Exact concentration and solvent depend on the specific indicator.
Temperature: Ambient (20–25°C) for consistent equilibria and endpoint sharpness.
Endpoint: Distinct color change of the free-dye form once EDTA complexes all Ca2+/Mg2+.
Interferences: Heavy metals, Fe3+, Mn2+, Cu2+, residual chlorine, and alkalinity can perturb endpoints. Masking agents (e.g., CN−, triethanolamine, tartrate) are used in some standardized methods; use only where safe and permitted.
Performance expectations
Under validated conditions, relative standard deviations below 1% are routinely achievable for total hardness in mid-ppm ranges (literature). Recovery and precision should be established during method validation with the chosen indicator.
Always confirm the exact dye, working concentration, and color transition behavior for SKU H196885 from its CoA/Spec Sheet before establishing conditions.
Safety and Handling
Authoritative safety data
GHS classification, pictograms, signal word, and H-statements: Not specified for this item; refer to the product SDS.
Research use: For research use only.
General laboratory precautions (good practice; not product-specific)
PPE: Wear lab coat, safety glasses, and appropriate chemical-resistant gloves. Avoid inhalation of dusts/aerosols and contact with skin/eyes.
Handling: Use in a well-ventilated area. Prevent contamination of reagents used for analytical titrations. Avoid ingestion and environmental release.
First aid (summary):
Inhalation: Move to fresh air; seek medical attention if symptoms persist.
Skin contact: Wash with soap and water; remove contaminated clothing.
Eye contact: Rinse cautiously with water for several minutes; seek medical attention if irritation persists.
Ingestion: Rinse mouth; seek medical attention as appropriate.
Stability and incompatibilities (general for azo dye indicators)
Store away from strong oxidizers and strong acids/bases unless formulation directions indicate otherwise.
Some dye indicators can fade under prolonged light exposure; keep solutions in amber glass when applicable.
Waste and spill response
Collect dye-contaminated waste according to institutional and regulatory guidance. Many metallochromic dyes are colored organics; minimize environmental release.
Always defer to the SDS and local regulations for definitive safety, handling, and disposal instructions specific to SKU H196885.
Solvent Selection
Applicability
As supplied here as a “hard water indicator,” the active color reagent is typically used in aqueous media during EDTA complexometric titrations, though stock solutions may be prepared in organic or mixed solvents. Item-specific solvent guidance is not provided; refer to CoA/Spec Sheet.
General solvent considerations for metallochromic indicators (literature)
Solubility: Many indicators dissolve better in ethanol, methanol, or isopropanol than in pure water; working stocks are often prepared in alcohol/water mixtures.
Titration medium: The analytical reaction is run in water buffered to alkaline pH (commonly pH ~10 with ammonia/ammonium chloride) to maintain EDTA in the Y4− form and optimize Ca2+/Mg2+ response.
Miscibility: Alcoholic stock solutions are fully miscible with water at typical usage levels.
Selection reasoning
Choose alcoholic stock if the dye shows limited aqueous solubility or to facilitate rapid dispersion in the titration flask.
Use amber glassware for light-sensitive dyes; avoid strongly basic solvents for storage unless specified, as they can promote dye degradation.
Comparison (general)
Water-only stock: Minimal background but may have solubility limits.
50–95% ethanol stock: Improved solubility and wetting; slight organic background introduced to titration.
Isopropanol stock: Similar benefits to ethanol with lower volatility.
Always confirm the recommended solvent system and concentration for SKU H196885 from its product documentation.
Storage and Reconstitution
Item-specific storage and shipping
Storage conditions: Room temperature (per product data).
Shipped in: Normal conditions (per product data).
General storage guidance (not item-specific)
Keep container tightly closed in a cool, dry place away from direct light. If supplied as a solution, store in amber glass where appropriate.
Prevent contamination with metal ions; use clean, dedicated scoops or pipettes.
Reconstitution/preparation notes (literature; confirm against CoA)
For dry dye: Prepare a stock solution in ethanol, isopropanol, or water as appropriate for the specific indicator; typical practice is to use alcoholic solvents to aid dissolution and dosing. Filter if insoluble particulates remain.
Working solutions: Store at room temperature protected from light; many indicator solutions are stable for weeks to months, but verify stability for the specific formulation.
Before critical assays, verify color response with a standard Ca/Mg solution to confirm performance.
Freeze–thaw guidance
Typically not applicable to dry solids. For solutions, avoid repeated freeze–thaw cycles which can precipitate or degrade dye; prepare aliquots if long-term storage is needed.
Always consult the product’s CoA/Spec Sheet for definitive instructions specific to SKU H196885.
Structure and Identity
This product is supplied under the functional description “Hard water indicator,” a class of colorimetric metallochromic indicators used to detect Ca2+/Mg2+ in complexometric titrations (e.g., EDTA hardness assays).
Item-specific identifiers
CAS: Not specified for this item; refer to CoA/Spec Sheet.
Molecular formula: Not specified for this item; refer to CoA/Spec Sheet.
Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.
SMILES: Not specified for this item; refer to CoA/Spec Sheet.
InChIKey: Not specified for this item; refer to CoA/Spec Sheet.
General structural notes (literature, not specific to this item)
Common hard water indicators include metallochromic azo dyes such as Eriochrome Black T (Mordant Black 11) and Calmagite. These typically feature:
One or more azo (–N=N–) linkages conjugated to phenyl/naphthyl rings.
Phenolic and/or sulfonic acid groups that enable metal chelation and water compatibility.
Multiple acid–base forms leading to pH-dependent color and metal–dye complexation equilibria.
In 2D terms, these structures show extended aromatic systems with azo bridges, ortho-phenolic donor sites, and sometimes sulfonate substituents for solubility.
Important note
Because “hard water indicator” can refer to different single dyes or proprietary blends, definitive structural identity for this catalog item is not specified here. Please consult the product’s CoA/Spec Sheet for the exact chemical identity and composition associated with SKU H196885.
Synthetic Utility
Scope
As a “hard water indicator,” this product functions as an analytical colorimetric reagent rather than a synthetic building block. It is not typically used to form covalent bonds or to partake in transformations in preparative organic or inorganic synthesis.
General chemistry notes (literature; not item-specific)
Metallochromic indicators are chelating ligands whose color depends on protonation state and metal complexation. They can, in principle, serve as probes in method development for chelation, ion exchange, or coordination chemistry studies.
Their strongly conjugated azo/phenolic frameworks can also be of pedagogical interest in pH and ligand-field demonstrations.
Recommendation
For synthetic applications requiring a chelating functionality, consider purpose-designed ligands (e.g., bipyridines, salen-type ligands, EDTA/NTA derivatives) rather than indicator dyes, which prioritize chromogenic behavior over catalytic or stoichiometric utility.
Target Specificity
Not applicable. This product is a chemical indicator, not a biological targeting reagent. No antigen/epitope specificity, clone, or isotype information applies to SKU H196885.
Utilizziamo i cookie per garantire il corretto funzionamento del sito web e, ove consentito, per migliorare la tua esperienza. Puoi gestire le tue preferenze in qualsiasi momento nelle Impostazioni. Per saperne di più, consulta la nostra Cookie Policy.
Desidera che le inviamo un messaggio quando avremo sconti disponibili?
Ricordamelo più tardi
Grazie! Controlli la sua casella di posta per confermare.
Products are supplied to verified businesses, institutions, and qualified professionals for research and development use only. Not for use in humans, animals, diagnosis, or therapy.