m-PEG5-sulfonic acid is a PEG derivative containing hydroxyl and sulfonic acid end groups. Sulfonic acid can participate in esterification, halogenation and replacement reactions. The hydrophilic PEG linker increases the water solubility of a compound in aqueous media. The hydroxyl group can be reacted to further derivatize the compound.
Specifiche
Specifiche e purezza
≥98%
Condizioni di conservazione di stoccaggio
Store at -20°C
Spedito in
Ice chest + Ice pads
Questo prodotto richiede spedizione a catena fredda. I servizi di terra e altri servizi economici non sono disponibili.
Purezza
≥98%
Nomi e identificatori
Peso molecolare
316.4
Dati avanzati
Certificati (CoA, COO, BSE/TSE e tabella di analisi)
Determine the necessary mass, volume, or concentration for preparing a solution.
Dilution Calculator
Determine the dilution needed to prepare a stock solution.
Reconstitution Calculator
Recensioni
Recensioni dei clienti
Application Protocols
No vendor-validated bioassay protocols are provided for this item.
For materials-focused use, the following general (literature-based) procedural outlines may be helpful. Always optimize for your system.
Preparation of sodium m-PEG5-sulfonate solution (stock): Dissolve the acid in water to a desired concentration (e.g., 10–100 mg/mL; user-defined) and titrate to pH 7–8 with NaOH to form the sodium salt. Filter (0.22 µm) to clarify. Store aliquots at −20°C for long-term or 4°C for short-term.
Surface pretreatment and coating: Clean substrates (plasma/UV-ozone for oxides or piranha for glass with appropriate safety). Immerse in 0.1–2 mg/mL PEG-sulfonate salt solution for 10–60 min, rinse thoroughly, and dry under nitrogen. Assess hydrophilicity by contact angle and charge by zeta potential.
Layer-by-layer film assembly: Alternate exposures to PEG-sulfonate (anionic) and a cationic polymer (e.g., PDADMAC) in 10–100 mM NaCl, pH 6–8, with 2–3 rinses between layers. Build to desired thickness; crosslink if needed using carbodiimide chemistry only if carboxylates are co-present.
Note
Exact concentrations, times, and rinsing protocols are system-specific; perform screening to establish optimal parameters for your substrate and performance goals.
Biological Roles
No biological (physiological) roles are assigned to this research material. The following points describe general behavior of PEG-sulfonate motifs in biochemical contexts (informational; not medical/clinical claims).
Bioinert hydration layer: PEG chains are well-known for resisting nonspecific protein adsorption due to steric repulsion and high-water structuring. A terminal sulfonate adds fixed negative charge, often further reducing fouling on proteins and cells in vitro.
Charge and ionic strength effects: Sulfonate groups are fully ionized across typical biological pH ranges, contributing to electrostatic exclusion of proteins and cells on coated surfaces and stabilizing colloids in physiological buffers.
Compatibility: PEG backbones are broadly regarded as biocompatible in research settings; however, the strong acidity of the free acid requires neutralization for contact with pH-sensitive biomolecules.
Interactions: Unlike multivalent sulfate motifs (e.g., heparin), a single terminal sulfonate on PEG5 generally exhibits minimal specific binding to proteins, behaving primarily as a nonspecific anionic solubilizer.
Note
This product is supplied for research use only. It is not intended for diagnostic, therapeutic, or clinical applications. Any in vitro use should be validated for cytotoxicity and compatibility, and surfaces should be thoroughly rinsed to remove unbound material.
Buffer Applications
This compound is a strong acid, not a classical buffering agent. Sulfonic acids (pKa < 0; literature) are fully dissociated above pH ~1, so they do not provide a useful conjugate acid/base pair within common buffer ranges.
Practical usage (general)
Ionic strength modifier: After neutralization to a sulfonate salt (e.g., Na+, K+, NH4+), solutions can be used to adjust ionic strength or to provide stable negative charge in polyelectrolyte assembly protocols.
pH adjustment: The free acid can lower pH, but without buffering capacity. Use standard buffers (e.g., MES, MOPS, HEPES, phosphate) for controlled pH environments.
Compatibility: PEG-sulfonates are typically compatible with many aqueous buffers. Avoid high concentrations of multivalent cations (Ca2+, Mg2+, Al3+) if precipitation/complexation is a concern; chelators (e.g., EDTA) can mitigate unintended crosslinking.
If your workflow requires a true buffer system, select a buffer with an appropriate pKa near your target pH and verify compatibility with PEG/sulfonate in small-scale trials.
Green Alternatives
Assessment focuses on solvent and platform choices, since the core PEG-sulfonic acid motif is already designed for aqueous processing.
Greener processing choices (literature-based)
Prefer water or bio-based alcohols (EtOH) over high-toxicity polar aprotics (DMF, NMP) when assembling coatings or doing ion-exchange steps.
If converting to sulfonyl chlorides/sulfonamides, consider reagents with improved profiles (e.g., sulfuryl chloride under controlled conditions) and solvents like MeCN or 2-MeTHF instead of DCM/DMF where compatible.
Functional alternatives and trade-offs
Carboxylate-PEG (m-PEG-CO2H): Greener coupling via EDC/NHS in water; however, lower charge retention at acidic pH and weaker electrolyte tolerance than sulfonates.
Sulfate-PEG (m-PEG-OSO3H/−): Can be made enzymatically and is highly water soluble, but sulfate esters are hydrolytically less robust than sulfonates on many surfaces.
Polyglycerol sulfonate (PGS): Derived from polyglycerol (renewable feedstocks); offers multivalent anchoring and high hydration. May alter viscosity and layer thickness relative to PEG5.
Comparison snapshot (general)
Sulfonate vs carboxylate: Sulfonate provides pH-independent charge and stronger ion pairing; carboxylate offers broader bioconjugation toolkits with milder reagents.
PEG vs polysaccharides (e.g., dextran sulfate): Polysaccharides are renewable and often biodegradable but can introduce batch-to-batch variability and specific biointeractions; PEG is more inert and consistent.
Waste minimization
Use aqueous workups and dialysis in place of repeated organic precipitations; reclaim alcohols by distillation; neutralize acid residues before disposal per local regulations.
Pharmaceutical Uses
No pharmacopeial status or excipient grade is provided for this item. It is offered for research use only.
Item-specific notes
Grade/excipient status: Not specified for this item; refer to CoA/Spec Sheet.
General, non-clinical formulation context (informational)
PEG-based anionic modifiers are sometimes investigated in R&D as solubilizing tags or as surface modifiers for devices and carriers, leveraging the combination of PEG hydration and sulfonate charge to reduce fouling and improve aqueous compatibility.
In preformulation research, converting the acid to a defined salt (e.g., sodium) can enhance stability, control osmolality, and improve handling in water-rich systems.
Analytical considerations: The presence of a strong anion can influence HPLC methods (ion-pairing, retention on anion-exchange). Validate analytical methods accordingly.
Compliance reminder
No claims are made for clinical, therapeutic, or diagnostic use. For any regulated applications, source materials with appropriate GMP/excipient grades and pharmacopeial monographs, and verify extractables/leachables for device-contact uses.
Physical Properties
Only limited item-specific physicochemical data are provided for this listing.
Item-specific values
Appearance: Not specified for this item; refer to CoA/Spec Sheet.
Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.
Molecular formula: Not specified for this item; refer to CoA/Spec Sheet.
Melting point, boiling point, density, refractive index, UV cutoff: Not specified for this item; refer to CoA/Spec Sheet.
Solubility: Not specified for this item; refer to CoA/Spec Sheet.
General/literature characteristics for PEG-sulfonic acid oligomers (informational only)
Physical state: Often low-melting solids or viscous syrups depending on exact oligomer distribution; hygroscopic tendency is common for short PEGs and sulfonic acids.
Solubility profile: Typically highly soluble in water and polar protic solvents (MeOH, EtOH) and polar aprotic solvents (DMSO, DMF). Limited solubility in nonpolar hydrocarbons. Strong electrolyte behavior upon neutralization to sulfonate salts.
Acid strength: Sulfonic acids are strong acids (pKa generally < 0; literature), fully ionized in water above pH ~1.
Partitioning: PEG chains confer hydrophilicity (literature: PEG oligomers have low logP); terminal sulfonate (as salt) further reduces hydrophobicity.
Notes for use
If precise water content, residual solvents, or average Mn are critical for your work, please consult the batch CoA/Spec Sheet. Because PEG oligomers may be supplied as distributions, some properties (e.g., exact MW) are reported as averages in the CoA.
Quality and Grades
Item-specific quality grade/purity are not listed for this product.
Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.
Stabilizers/additives: Not specified for this item; refer to CoA/Spec Sheet.
How to interpret common quality notes (general guidance)
Research grade: Suitable for most R&D workflows. If present, reported purity typically reflects organic assay and/or average oligomer distribution for PEG materials.
Polymer/oligomer distributions: For PEG n=5 materials, suppliers may report average Mn (number-average) and polydispersity (Đ). Verify averages on the batch CoA if exact stoichiometry is required (e.g., for quantitative conjugation chemistry).
Residuals and metals: For surface/nanomaterials applications, residual metal catalysts or inorganic salts can impact performance. If these are critical, request a trace metals or IC report.
Water/volatile content: PEG oligomers and sulfonic acids can be hygroscopic. Karl Fischer water and residual solvent data, when critical (e.g., for precise acid equivalents), should be sourced from the CoA.
What is specific to this item
Storage requirement of −20°C and cold shipment indicate moisture/thermal sensitivity consistent with short PEG sulfonic acids. For precise average MW, acid value, and neutralization equivalent, consult the batch CoA/Spec Sheet.
Reaction and Applications
This reagent serves as a compact, anionic, hydrophilic handle for materials science and surface/interface chemistry.
Representative applications (general/literature)
Surface functionalization: Introduces durable negative charge and hydration shell on oxides (SiO2, Al2O3), metals (Au, Ag), and carbon materials via physisorption or multivalent interactions of PEG while the sulfonate provides fixed charge; ideal for antifouling and colloidal stability.
Nanoparticle stabilization: PEG-sulfonates can prevent aggregation in aqueous dispersions; the strong acid ensures ionization over a broad pH range, improving zeta potential control and electrolyte tolerance.
Polyelectrolyte multilayers: Acts as a strong polyanion component in LbL assemblies, especially with polycations (e.g., PEI, PDADMAC), yielding salt- and pH-resistant films.
Ionic tags/phase modifiers: The sulfonate imparts water solubility to otherwise hydrophobic motifs in small-molecule libraries when used as a solubility tag; facilitates purification by ion-exchange.
Precursors to sulfonyl derivatives: Conversion of the terminal –SO3H to sulfonyl chlorides, sulfonamides, or sulfonate esters enables covalent attachment to nucleophiles (amines, alcohols), using the PEG as a hydrophilicity modulator.
Practical notes
Control ionization: Use defined counterions (Na+, K+, TBA+) to tune solubility in mixed solvents and to modulate film assembly.
For coatings, pre-clean substrates, then apply from aqueous or alcohol solutions; rinse and cure as needed. Verify loading via contact angle, XPS/S, or zeta potential.
Reaction Conditions
The following reaction conditions are literature-based general guidance for sulfonic acid to sulfonyl derivatives and for polyelectrolyte assembly with PEG-sulfonates. Adjust to your substrate and verify on small scale.
Salt formation (aqueous): Add 1.0–1.05 equiv of base (NaOH, KOH, NH4OH) at 0–25°C in water or water/alcohol. Maintain pH 7–9 to avoid excess base. Isolate by lyophilization or solvent removal. Typical conversions are quantitative.
Sulfonyl chloride formation: React with SOCl2 (3–5 equiv) or SO2Cl2 (2–3 equiv) in anhydrous DCM, MeCN, or DMF (0.05–0.2 M) at 0–25°C, 1–4 h. Catalytic DMF (0.05–0.1 equiv) can accelerate. Remove volatiles under reduced pressure; use immediately to form sulfonamides/esters. Typical isolated yields for downstream sulfonamides: 60–90% (substrate-dependent; literature).
Sulfonamide formation: Combine sulfonyl chloride with amine (1.1–1.5 equiv) and base (2–3 equiv, e.g., Et3N, DIPEA) in DCM/MeCN at 0–25°C for 1–6 h. Work up by aqueous washes; purify by preparative RP-HPLC if needed due to PEG polarity.
Layer-by-layer assembly: Prepare 0.1–2 mg/mL solutions of PEG-sulfonate salt and a polycation (e.g., PDADMAC) in 10–100 mM NaCl, pH 6–8. Alternate 5–10 min adsorption and rinsing cycles on cleaned substrates. Monitor growth by QCM-D or UV-vis of tracer dyes.
Notes
Drying: For non-aqueous chemistry, azeotropically remove water (e.g., with toluene) or vacuum-dry prior to activation.
Analytics: Titrate acid value to confirm equivalents; use ion chromatography for residual chloride after SOCl2 steps; characterize by 1H/13C NMR and HRMS (adducts often appear as [M+Na]− for sulfonates).
Safety and Handling
Safety data specific to this item are not provided in the listing; consult the SDS for authoritative guidance.
Item-specific hazard data
GHS classification, signal word, pictograms, H-statements: Not specified for this item; refer to SDS.
General safety considerations for PEG-sulfonic acids (informational only)
Corrosivity/acid hazards: Sulfonic acids are strong acids; they may cause skin/eye irritation or burns. Neutralized sulfonate salts are generally less irritating but can be hygroscopic.
Incompatibilities: Avoid strong bases without appropriate controls (exotherm, heat). Avoid strong dehydrating agents and acid chlorinating reagents unless intended (may form sulfonyl chlorides). Oxidizers are typically compatible with PEG backbones, but exercise standard caution.
Peroxide formation: Ether-containing materials can form peroxides over long storage with air/UV; although low for short PEG oligomers in aqueous media, minimize unnecessary peroxide exposure and check when concentrating from air-exposed organic solvents.
PPE and handling
Recommended PPE: Lab coat, safety glasses, acid-resistant gloves (e.g., nitrile). Work in a fume hood when charging powders or using reactive chlorinating agents.
First aid (overview; follow SDS): Eye/skin contact—rinse with water for ≥15 minutes, remove contaminated clothing. Inhalation—move to fresh air. Ingestion—rinse mouth; seek medical advice.
Storage and transport
Storage: Store at −20°C (per Product Data). Protect from moisture; keep tightly closed.
m-PEG5-sulfonic acid is a highly polar, hydrophilic oligomer; solvent choice dictates ionization state, handling, and downstream application.
General/literature solvent behavior
Water: Typically fully miscible; strong acid will be ionized above pH ~1. Salts (Na+, K+, NH4+) are readily formed and highly water soluble.
Alcohols (MeOH, EtOH, iPrOH): Good solubility; useful for stock solutions and coatings. Acid remains largely unionized; avoid prolonged exposure of equipment susceptible to acid corrosion.
Polar aprotics (DMSO, DMF, NMP): Excellent solvency for PEG chains; suitable for surface modification protocols and coupling to generate sulfonyl derivatives.
Acetonitrile: Often miscible; solubility may be formulation-dependent.
Nonpolar solvents (hexanes, toluene): Poor solubility; use co-solvents or convert to a counterion pair with lipophilic cations for phase transfer.
Selection tips
For electrostatic surface modification or polyelectrolyte assembly: Use aqueous media, optionally buffered, and neutralize to the desired sulfonate salt.
For synthesis of sulfonyl chlorides/sulfonamides: Employ dry polar aprotics (e.g., DCM/DMF mixes, acetonitrile) under anhydrous, base-scavenged conditions.
For nanoparticle stabilization: Water or low alcohols minimize organic residue and enable easy dialysis.
Small comparison (literature-based)
Sulfonic acid vs carboxylic acid PEG: Sulfonic acids are stronger (full ionization at low pH), providing more stable surface charge in acidic media; carboxylates offer easier coupling to amines via carbodiimides but are pH-sensitive.
Storage and Reconstitution
Item-specific storage
Storage conditions: Store at −20°C (per Product Data). Keep container tightly closed. Protect from moisture and prolonged exposure to air.
General handling and reconstitution guidance (informational)
Hygroscopicity: PEG oligomers and sulfonic acids can absorb moisture. Minimize headspace, use desiccant, and allow containers to warm to room temperature in a desiccator before opening to prevent condensation.
Solid-to-solution preparation: Dissolve in water, alcohols, or polar aprotic solvents as compatible with your application. For biological or colloidal work, prepare aqueous solutions and, if needed, neutralize to the desired sulfonate salt with standardized base.
Stock solutions: Not specified for this item; refer to CoA/Spec Sheet. As a general practice, prepare user-defined concentrations, sterile-filter if required, and store aliquots to avoid repeated freeze–thaw.
Freeze–thaw: Repeated cycles can concentrate impurities via evaporation. Prepare single-use aliquots and thaw at room temperature; mix thoroughly before use.
Stability: Not specified for this item; refer to CoA/Spec Sheet. In general, avoid strong oxidants and dehydrating chlorinating agents unless intentionally used for derivatization. Monitor pH and ionic strength for long-term aqueous storage.
Always consult the batch CoA and SDS for definitive storage limits and compatibility prior to critical experiments.
Structure and Identity
A PEGylated, strongly acidic, anionic linker featuring a terminal sulfonic acid on a short monodisperse PEG chain (nominally 5 ethylene oxide units). Useful as a hydrophilic, charge-imparting handle for materials and surface chemistries.
SKU: M595642
Product name: m-PEG5-sulfonic acid
CAS: 1807505-35-6
Category: Materials science (research use only)
Item-specific identifiers
Molecular formula: Not specified for this item; refer to CoA/Spec Sheet.
Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.
SMILES: Not specified for this item; refer to CoA/Spec Sheet.
InChIKey: Not specified for this item; refer to CoA/Spec Sheet.
Structural features (general description; literature-based)
Backbone: Poly(ethylene glycol) (PEG) chain with approximately five –CH2–CH2–O– repeats, capped at one terminus with a methyl ether (m-PEG) and at the other with a sulfonic acid group (–SO3H).
Functional groups: Ether repeats (PEG), terminal strong acid (sulfonic acid). Expected to be anionic under virtually all neutral/alkaline conditions (pKa of sulfonic acids typically < 0; literature).
Topology: Flexible, hydrophilic oligomer; no rings; no stereocenters. The PEG segment imparts high water miscibility and low protein adsorption; the sulfonic acid provides fixed negative charge and salt-forming capability.
2D description in words
A linear chain of five ethylene glycol units begins at a methoxy cap (–O–CH3), continues through repeating –CH2–CH2–O– linkages, and terminates in an alkyl spacer tethered to a –SO3H group, yielding an amphiphilic but overall highly hydrophilic, anionic terminus.
Synthetic Utility
m-PEG5-sulfonic acid is a modular building block combining a hydrophilic PEG handle with a terminal strong acid. It enables both covalent derivatization of the sulfonyl moiety and noncovalent, charge-based interactions.
Transformations (general/literature)
Salt formation: Quantitative neutralization with alkali (NaOH, KOH), ammonium, or organic bases (TEA, TBA) provides sulfonate salts with tunable solubility in mixed solvents.
Activation to sulfonyl chlorides: Treatment with thionyl chloride or sulfuryl chloride (often with catalytic DMF) affords the corresponding sulfonyl chloride, enabling formation of sulfonamides (with amines) or sulfonate esters (with alcohols).
Coupling to polymers/surfaces: Sulfonate salts can ionically pair with cationic polymers (PEI, PDADMAC) to form layer-by-layer films; sulfonyl chlorides allow covalent grafting to nucleophilic surfaces (amine-terminated substrates).
Ion-pair extraction: Association with lipophilic ammonium cations can render the complex soluble in organic media for phase-transfer strategies.
Utility of the PEG5 segment
Solubility tag: Increases water and polar solvent solubility of appended motifs; facilitates purification by ion-exchange or SEC.
Spacing and flexibility: Provides a short, flexible spacer to distance the charged group from surfaces or cores, beneficial for colloidal stabilization and minimizing steric hindrance in conjugation.
Notes
Verify the average molecular weight/acid value from the CoA to calculate equivalents accurately in stoichiometric transformations.
Target Specificity
Not an antibody or biological targeting reagent. No antigen/epitope or species reactivity applies to this product.
Target/epitope: Not applicable.
Clone/isotype: Not applicable.
Any specificity data would be out of scope; for materials functionalization, see Reaction & Applications and Synthetic Utility sections.
Domande frequenti
What is the purity of this product?
This product is supplied at ≥98% purity (chemical assay). Lot-specific values are stated on the Certificate of Analysis.
How should this product be stored?
Store at ?20 °C. Freezer storage is required to maintain the specified shelf life.
How is this product shipped?
This product ships in an insulated container with ice pads. Unpack on arrival and transfer it to the storage condition stated above.
What are the CAS number, molecular formula and molecular weight?
The CAS Number is 1807505-35-6, the molecular formula is C11H24O8S, and the molecular weight is 316.4 g/mol.
What documentation is provided?
Available product documentation, including Certificates of Analysis (COA), Safety Data Sheets (SDS), and specification sheets, is shown in the product document area. Document availability and access follow the current site policy.
Utilizziamo i cookie per garantire il corretto funzionamento del sito web e, ove consentito, per migliorare la tua esperienza. Puoi gestire le tue preferenze in qualsiasi momento nelle Impostazioni. Per saperne di più, consulta la nostra Cookie Policy.
Desidera che le inviamo un messaggio quando avremo sconti disponibili?
Ricordamelo più tardi
Grazie! Controlli la sua casella di posta per confermare.
Products are supplied to verified businesses, institutions, and qualified professionals for research and development use only. Not for use in humans, animals, diagnosis, or therapy.