mPEG propionaldehyde - MW 2000 Da

Cat. No.: M164005
Disponible para pedir
CALIDAD & PUREZA MW 2000 Da
Storage
Store at -20°C,Argon charged
Shipped In
Ice chest + Ice pads
★
Talla
Alemania (EU)
USA*
Precio
Cantidad
250mg
m164005-250mg
—
2 Disponible

137,88€

179,54€
Guardar 41,65 € (23.20%)
1g
m164005-1g
—
2 Disponible

392,13€

462,42€
Guardar 70,29 € (15.20%)
Enter a quantity for the sizes you want to add.

Descripción general

Methoxy PEG propionaldehyde is a stable aldehyde PEG that can be used for protein, antibody, peptides or carbohydrate N-terminal amine group pegylation reagent. The reaction between aldehyde group with the α-amine at the N-terminus produces an intermediate Schiff base. Further reduction with hydride will form a stable C-N bond. PEG aldehydes react with n-terminus amine groups at a pH of from 5.0 to 9.5. Higher pH will result in multiple Pegylation with both terminal and lysine groups.

Especificaciones

Especificaciones y pureza
MW 2000 Da
Condiciones de almacenamiento de almacenamiento
Store at -20°C,Argon charged
Enviado en
Ice chest + Ice pads
Este producto requiere envío en cadena de frío. Los servicios terrestres y otros servicios económicos no están disponibles.

Datos avanzados

Certificados (CoA, COO, BSE/TSE y tabla de análisis)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:

Find and download the COA for your product by matching the lot number on the packaging.

2 results found

Lot NumberCertificate TypeFechaArticulo
C2211457C2211457Certificate of AnalysisDec 10, 2024 M164005
C2211465C2211465Certificate of AnalysisDec 10, 2024 M164005
Propiedades químicas y físicas
SolubilidadSoluble in water, DMSO, DMF
Preguntas frecuentes y artículos
Calculadoras de soluciones
Reseñas

Reseñas de cliente

Application Protocols

Item-specific, tested protocols: Not provided for this item; refer to your application and consult primary literature.

General example workflows (literature/general)

  • Reductive amination PEGylation (aqueous)
    • Dissolve target amine-bearing biomolecule in 100 mM phosphate buffer, pH 6.3.
    • Add mPEG–propionaldehyde at desired molar excess relative to accessible amines (e.g., 2–10× for proteins, higher for small molecules).
    • Incubate 30–60 min, then add NaBH3CN to 20–30 mM; continue 2–16 h at 4–25°C with gentle mixing.
    • Quench residual aldehyde (e.g., ethanolamine), then purify by SEC or UF.
  • Oxime ligation to aminooxy partner
    • Prepare 100 mM sodium acetate, pH 5.0, with 50 mM aniline.
    • Mix mPEG–propionaldehyde with aminooxy substrate (1–5× excess PEG for biomolecules) and incubate 1–6 h at room temp.
    • Optionally reduce to secondary amine, then purify.

Controls and analytics

  • Include a no-reductant control to assess imine formation; monitor with SEC, SDS-PAGE, or MS as appropriate.
  • Determine remaining free amines with TNBS/OPA assays; confirm conjugation via mass shift or SEC elution changes.
Biological Roles

Applicability to this product

  • Item-specific biological role claims are not provided. This product is for research use only.

Literature/general context

  • PEG as a material: Poly(ethylene glycol) is widely regarded as biologically inert, nonionic, and protein-resistant, reducing nonspecific adsorption on surfaces and biomaterials.
  • Bioconjugation handle: The terminal aldehyde reacts with primary amines (after imine formation) or with hydrazide/aminooxy groups, enabling site-selective attachment of PEG to biomolecules, surfaces, and nanoparticles.
  • Effect on biomolecules: PEGylation can alter hydrodynamic size, reduce nonspecific interactions, and modulate biophysical properties such as solubility and aggregation in vitro. These are system- and degree-of-labeling–dependent phenomena.
  • Enzymatic compatibility: Aldehyde-based ligations are typically performed under mild, near-physiological conditions that preserve protein secondary structure; buffer composition and pH require optimization to avoid unwanted Schiff base formation with off-target residues.

Notes

  • Avoid clinical or therapeutic extrapolations; suitability must be demonstrated empirically for each biological system in research settings only.
Buffer Applications

Item-specific

  • No buffer specifications are provided for this item; consult your application requirements.

Literature/general guidance for aldehyde conjugations

  • Buffer selection principles
    • Avoid primary-amine buffers (e.g., Tris, glycine) which compete with targets during aldehyde ligations.
    • Favor phosphate, HEPES, or acetate buffers depending on pH.
  • Typical conditions (general)
    • Reductive amination to amines: 50–200 mM phosphate or acetate, pH 6.0–7.0; 10–50 mM NaBH3CN or NaBH(OAc)3; 4–25°C; 2–24 h.
    • Oxime/hydrazone ligation: 50–200 mM acetate, pH 4.5–5.5; optional 10–100 mM aniline catalyst; 4–25°C; 1–16 h; optional post-reduction for stability.
  • Cosolvents
    • Up to 10–30% DMSO or ethanol can aid solubility of hydrophobic partners; confirm compatibility with biomolecules.
  • Practical tips
    • Degas buffers and maintain inert atmosphere when possible to limit aldehyde oxidation.
    • After reaction, quench unreacted aldehyde (e.g., with bisulfite or ethanolamine) before downstream analyses if needed.
Green Alternatives

Context

  • mPEG–propionaldehyde is frequently used in aqueous or mixed aqueous systems, enabling relatively green processes compared to strictly organic-phase reactions. Greener choices often revolve around solvent selection and reaction catalysts.

Greener options (literature/general)

  • Solvent choice
    • Prefer water or aqueous acetate/phosphate buffers when feasible; add small percentages of ethanol over higher-toxicity cosolvents when miscibility allows.
    • Replace DMF/DMAC with safer polar aprotics such as Cyrene or propylene carbonate in compatible transformations (evaluate solubility and kinetics for your specific substrate).
    • For organic-phase reactions, consider 2-methyltetrahydrofuran (2-MeTHF) instead of THF and ethyl acetate instead of DCM when appropriate.
  • Catalysis
    • Use aniline or p-aminobenzoic acid as organocatalysts for oxime/hydrazone ligations, minimizing metal waste.
  • Process intensification
    • Perform conjugations at ambient temperature to reduce energy use; leverage high-concentration aqueous solutions to minimize solvent volume.

Illustrative comparison (general)

  • Water/buffer vs. DMF-rich media
    • Environmental: Water has superior EHS profile; DMF is reproductive toxin.
    • Performance: Water may slow imine formation; add benign catalysts and adjust pH to 5–6 to compensate.

Trade-offs

  • High water content can hydrate aldehydes and slightly reduce effective electrophilicity; process design (pH, catalysts, stoichiometry) mitigates this while maintaining a greener footprint.
Pharmaceutical Uses

Item-specific

  • No pharmacopeial grade or excipient status is provided for this item. For research use only.

Literature/general context

  • Process reagent: mPEG–propionaldehyde is commonly employed in research-scale manufacture of PEG–biomolecule conjugates via aldehyde-based ligations (e.g., to amines, hydrazides, or aminooxy-bearing substrates) under mild aqueous conditions.
  • Formulation relevance: PEGylation can alter solubility and colloidal stability of proteins or nanoparticles in research formulations; however, excipient-grade compliance, residual solvent limits, and endotoxin/bioburden controls must be verified for any regulated use.
  • Analytical considerations: Characterization typically includes SEC for size distribution, LC–MS/peptide mapping for conjugation sites (proteins), TNBS/OPA assays for free amines, and GPC for polymer metrics.

Note

  • No therapeutic or clinical claims are made. If GMP or pharmacopeial compliance is required, request documentation specific to that purpose; this listing does not specify such qualifications.
Physical Properties

Item-specific (from Product Data)

  • Appearance, Molecular weight, Refractive index, Density, BP/MP, Solubility: Not specified for this item; refer to CoA/Spec Sheet.

Literature/general expectations for mPEG–propionaldehyde (chain-length dependent)

  • Physical state: Typically a white to off-white solid or waxy material at ambient temperature for mid-to-high MW; lower MW grades may be viscous liquids.
  • Solubility: Highly soluble in water and polar organic solvents (e.g., methanol, ethanol, DMSO, DMF); limited solubility in nonpolar hydrocarbons. The terminal aldehyde remains hydrated to a small extent in water, especially at low pH.
  • Partitioning: Overall hydrophilic with very low logP due to PEG backbone; aldehyde end-group adds only modest hydrophobicity.
  • Thermal behavior: No sharp boiling point; exhibits softening point/glass transition that depends strongly on Mn and polydispersity. PEG segments show characteristic melting transitions that decrease with increasing dispersity (values are grade-specific).
  • Hygroscopicity: PEG chains are hygroscopic; material can pick up moisture which may affect aldehyde reactivity.

Practical implications

  • Use freshly dried solvents or desiccated conditions for accurate stoichiometry in conjugations.
  • If viscosity hinders handling, gentle warming (e.g., 30–40°C) can aid dissolution; avoid prolonged heating that may accelerate oxidation of the aldehyde group.
Quality and Grades

Item-specific (from Product Data)

  • Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.
  • Item-specific storage: −20°C, argon charged (from Product Data).

How to interpret typical quality attributes for mPEG–aldehydes (literature/general)

  • Functional purity: Often reported as “aldehyde content” or conversion (%) of end-groups. High functional purity is critical for efficient conjugation.
  • Molecular weight metrics: CoA commonly lists Mn, Mw, dispersity (Đ), and method (e.g., GPC vs. NMR). These are lot-dependent for polymers.
  • Residuals: Solvent residues (e.g., toluene, MeOH, DCM), catalyst traces, and unreacted PEG species are usually controlled; verify via CoA if limits are important for your application.
  • Water content: Karl Fischer moisture can influence conjugation efficiency; dryness is typically specified on CoA. Not specified for this item; refer to CoA/Spec Sheet.
  • Stabilizers: Aldehyde PEGs are generally shipped without stabilizers; inert-atmosphere packing helps preserve the carbonyl functionality. If stabilizers are used, they should be disclosed on the CoA (not provided here).

Practical guidance

  • For quantitative bioconjugation, confirm aldehyde content and Mn by CoA/NMR before use.
  • For reproducibility, use a single lot for critical studies and record the exact Mn and Đ.
  • If low UV background is needed (e.g., analytical HPLC of conjugates), request UV-cutoff data or HPLC-grade information where applicable (not provided here).
Reaction and Applications

Item-specific

  • Manufacturer Applications: Not specified beyond product naming; this reagent is intended for research use only.

Literature/general applications for mPEG–propionaldehyde

  • Reductive amination to primary amines: Forms stable secondary alcohols after in situ imine formation and reduction (NaBH3CN or NaBH(OAc)3), widely used for PEGylating amine-bearing ligands, peptides, or surfaces.
  • Hydrazone/oxime ligation: Reaction with hydrazides or aminooxy groups yields hydrazones/oximes; can be driven to completion by mild acid catalysis (pH 4.5–5.5) and aniline catalysts, then optionally reduced for permanence.
  • Acetal/ketal chemistry: Protection of the aldehyde as acetals using diols (e.g., ethylene glycol) for subsequent transformations on the PEG chain.
  • Polymer/materials modification: Installation of an aldehyde handle on surfaces or nanoparticles through mPEG–CHO end groups for further bioconjugation, antifouling coatings, or crosslinking with bis-hydrazides.
  • Ligation site selectivity: N-termini of proteins often show enhanced selectivity for aldehyde conjugation at mildly acidic pH versus lysines; confirm by MS mapping.

Practical tips

  • Control pH to balance imine formation and protein stability (often pH 6.0–6.5).
  • Use freshly prepared solutions, exclude competing nucleophiles (avoid Tris, primary-amine buffers).
  • Monitor progress by SEC, SDS-PAGE, LC–MS of digests, or TNBS assay for remaining amines.
  • Quench unreacted aldehyde with excess glycine or sodium bisulfite when needed.
Reaction Conditions

Item-specific

  • No tested reaction conditions are provided for this item. The following are literature/general guidelines; optimize for your system.

Typical literature conditions

  • Reductive amination (aqueous)
    • Substrates: Primary amine-bearing ligands/biomolecules.
    • Buffer: 50–200 mM phosphate or acetate, pH 6.0–6.5 (avoid Tris).
    • Reductant: NaBH3CN (10–50 mM) or NaBH(OAc)3 (10–30 mM) added after brief pre-incubation of aldehyde + amine.
    • Temperature/time: 4–25°C, 2–24 h. Monitor by SEC or TNBS assay.
  • Oxime/hydrazone ligation
    • Partner: Aminooxy or hydrazide derivative.
    • Buffer: 100 mM acetate, pH 4.5–5.5; aniline (10–100 mM) as nucleophilic catalyst.
    • Temperature/time: 4–25°C, 1–16 h; optional reduction (e.g., NaBH3CN) to convert to stable alkyl oxime/hydrazide linkages.
  • Acetal formation (organic)
    • Solvent: Anhydrous MeOH or toluene with Dean–Stark when using diols.
    • Catalyst: p-TsOH or other acid catalysts in catalytic amounts; remove water to drive equilibrium.

General notes

  • Oxygen and moisture accelerate aldehyde oxidation; perform reactions under inert gas when possible.
  • For viscous solutions, use overhead stirring, mild heating (≤40°C), and higher dilution to improve mass transfer.
  • Purification: Dialysis/UF for bioconjugates; precipitation into cold ether or acetone for polymeric products.
Safety and Handling

Item-specific (from Product Data)

  • GHS classification, Signal word, H-statements, Pictograms: Not specified for this item; refer to the product SDS for authoritative safety information.
  • Storage guidance: Store at −20°C under argon (provided). Shipments are cold-packed.

General safety considerations (literature/general)

  • Hazard profile: PEG backbones are generally of low acute toxicity; however, aldehydes are electrophilic and can cause irritation to skin, eyes, and respiratory tract. Avoid inhalation of dust/aerosols and contact with skin/eyes.
  • PPE: Wear lab coat, safety goggles, and appropriate chemically resistant gloves (e.g., nitrile). Use in a well-ventilated area or fume hood when weighing/dissolving.
  • Incompatibilities: Strong oxidizers (can over-oxidize aldehyde/backbone), strong reducing agents (may reduce aldehyde), strong bases (promote aldol/self-reactions), and amines without control (unintended imine formation). Avoid acids or bases during long-term storage.
  • Stability notes: Aldehyde end can oxidize to the corresponding acid; minimize exposure to air/oxygen and moisture. Re-purge headspace with inert gas after each use.
  • First aid (summary; defer to SDS): In case of skin/eye contact, rinse with plenty of water for several minutes; remove contaminated clothing. If inhaled, move to fresh air. If ingested, rinse mouth and seek medical advice. Provide SDS to healthcare personnel.
  • Waste: Collect aqueous and organic PEG-containing waste per institutional guidelines. Aldehyde-containing residues may require segregation and carbonyl quenching per local regulations.
Solvent Selection

Item-specific

  • No item-specific solvent restrictions are provided beyond storage; consult CoA/SDS for compatibility. Store under inert gas to protect the aldehyde.

Literature/general solvent behavior and selection

  • Polarity class: Highly polar, hydrogen-bond accepting polyether with terminal aldehyde. Excellent water miscibility for many Mn ranges and strong solubility in polar organics (MeOH, EtOH, DMSO, DMF, acetonitrile). Limited solubility in alkanes.
  • Conjugation contexts:
    • Aqueous buffers (phosphate, acetate) at pH ~5–7 for hydrazone/oxime formation or reductive amination to amines.
    • Mixed solvents (e.g., 10–50% DMSO or DMF in buffer) to solubilize hydrophobic targets while maintaining reactivity.
  • Dry organic media: For small-molecule synthesis (e.g., acetal formation, reductive amination with organic-soluble amines), use anhydrous MeOH, EtOH, THF, DCM, or toluene depending on the reaction.

Comparison (general)

  • Water/buffer: Green, biocompatible; may hydrate aldehyde and slow kinetics; add catalysts (e.g., aniline) for oxime/hydrazone.
  • DMSO/DMF cosolvent: Improves solubility and rate with hydrophobic substrates; consider downstream removal and potential amine scavenging.
  • Alcohols (MeOH/EtOH): Good for acetals and NaBH(OAc)3 reductions; avoid excess base to limit side reactions.

Tips

  • Degas aqueous buffers and minimize primary amines in buffers unless intentionally reacting (avoid Tris during aldehyde conjugation).
Storage and Reconstitution

Item-specific (from Product Data)

  • Storage conditions: Store at −20°C, Argon charged (maintain inert atmosphere to protect the aldehyde end-group).
  • Shipping: Ice chest + ice pads.

General best practices (literature/general)

  • Handling
    • Allow container to equilibrate to room temperature under inert gas before opening to minimize condensation.
    • After use, promptly re-purge headspace with argon or nitrogen and tightly reseal.
    • Minimize exposure to air, light, and moisture to limit aldehyde oxidation to acids.
  • Reconstitution
    • Solvents: Water, PBS (avoid for conjugations due to phosphate reactivity with metals only; acceptable generally), acetate or phosphate buffers, or polar organics (DMSO, DMF, MeOH, EtOH) depending on application.
    • Concentration: Prepare stock solutions at 10–100 mg/mL as solubility allows; filter (0.22 µm) if needed for bioconjugations.
    • Aliquoting: Prepare single-use aliquots to avoid repeated freeze–thaw. Store solutions at −20°C (short term) or −80°C (longer term) under inert gas; confirm stability empirically.
  • Stability checks
    • Monitor aldehyde integrity by 1H NMR (formyl proton ~9–10 ppm), bisulfite adduct test, or functional assays (e.g., reaction with aniline).
    • Discard if significant oxidation (loss of aldehyde signal) or discoloration/precipitation is observed.

Note

  • Specifications such as water content, aldehyde content, and exact Mn are not provided here; consult the lot-specific CoA/Spec Sheet for definitive guidance.
Structure and Identity

Item-specific (from Product Data)

  • Product name: mPEG propionaldehyde (monomethoxy poly(ethylene glycol) bearing a terminal propionaldehyde functionality)
  • Storage: Store at −20°C, Argon charged (inert atmosphere)
  • Shipped: Ice chest + ice pads
  • CAS, InChIKey, SMILES, Molecular formula, Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.

General structural description (literature/general)

  • Core motif: A linear poly(ethylene glycol) chain (–CH2–CH2–O–)n that is monofunctionalized on one end with a methoxy cap (–O–CH3) and on the other end terminated with a propionaldehyde group (–CH2–CH2–CHO).
  • Functional groups: Terminal aliphatic aldehyde (electrophilic carbonyl), polyether backbone (repeating ether units), terminal methyl ether cap (nonreactive end).
  • Polydispersity: mPEG materials are typically polydisperse; number-average molecular weight (Mn) and dispersity (Đ) are normally specified on the CoA for a given lot (not provided here).
  • 2D structure (described): A methoxy group attached to an ethoxy repeat chain of variable length, ending with a –CH2–CH2–CHO unit; no rings or stereocenters. The molecule is linear and highly flexible due to ether linkages.

Notes

  • Because the exact chain length distribution is not provided, treat values such as MW and elemental formula as variable and lot-specific. Always consult the CoA for precise identity attributes (Mn, Mw, Đ, aldehyde content).
Synthetic Utility

General synthetic value of mPEG–propionaldehyde (literature/general)

  • Electrophilic carbonyl handle: The terminal aldehyde enables a wide range of carbonyl transformations under mild conditions compatible with sensitive payloads.
  • Key transformations
    • Reductive amination with primary amines to install secondary amine-linked PEGs.
    • Formation of imines, hydrazones, and oximes with subsequent optional reduction to stabilize linkages.
    • Acetal protection with diols; reversible under acid to regenerate the aldehyde.
    • Nucleophilic additions (e.g., cyanohydrin formation or bisulfite adducts) for temporary masking or purification.
    • Wittig/olefination with stabilized ylides to append vinyl substituents; often requires organic media and careful control due to polymer solubility/viscosity.
  • Polymer/platform chemistry
    • Surface grafting: Reaction with amine-functional surfaces (e.g., aminosilanized silica, amine-terminated polymers) for antifouling coatings.
    • Crosslinking: Use with dihydrazides or diaminooxy linkers to form PEG-containing networks and hydrogels.

Practical considerations

  • Stoichiometry is governed by end-group functionality; confirm aldehyde content to achieve predictable degrees of functionalization.
  • Viscosity and mass transfer can limit rates; increase mixing efficiency and consider mild heating when compatible.
  • Purification often relies on dialysis, ultrafiltration, or precipitation rather than chromatographic methods due to polymeric nature.
Target Specificity

Not applicable to this reagent.

  • This product is a functionalized polymer (mPEG–propionaldehyde) and is not an antibody or targeted biological reagent. No antigen/epitope specificity, clone, isotype, or species reactivity applies to this item.
  • For selectivity in use, see Reaction & Applications and Buffer Applications for guidance on chemoselective ligation to amines, hydrazides, or aminooxy groups.

Preguntas frecuentes

How should this product be stored?
Store at ?20 °C under argon. It is supplied under an argon blanket; reseal under inert gas after each use.
How is this product shipped?
This product ships in an insulated container with ice pads. Unpack on arrival and transfer it to the storage condition stated above.
What documentation is provided?
Available product documentation, including Certificates of Analysis (COA), Safety Data Sheets (SDS), and specification sheets, is shown in the product document area. Document availability and access follow the current site policy.

¿Quieres que te enviemos un mensaje cuando tengamos descuentos disponibles?

Recordármelo más tarde

¡Gracias! Por favor, revisa tu bandeja de entrada de correo electrónico para confirmar.

¡Vaya! Las notificaciones están desactivadas.