Determine the necessary mass, volume, or concentration for preparing a solution.
Dilution Calculator
Determine the dilution needed to prepare a stock solution.
Reconstitution Calculator
Reviews
Customer Reviews
Application Protocols
General laboratory protocol for OPV device fabrication using O-IDTBR (literature/example workflow):
Substrate preparation
Patterned ITO glass: sequential sonication (detergent, DI water, acetone, IPA), N2 dry, UV–ozone 10–20 min.
Deposit electron-selective interlayer: spin-coat ZnO nanoparticle dispersion or ALD SnO2; bake per supplier guidance.
Active-layer ink
Prepare donor:O-IDTBR blend at 1:1 to 1:1.5 (w/w), total solids 15 mg/mL in CB or o-DCB.
Heat to 90–100 °C with stirring 1–2 h; filter hot through 0.2 μm PTFE; keep protected from light.
Optional: add 1 vol% DIO; re-filter.
Coating
Spin-coat 1500–2500 rpm, 30–60 s to get ~100–150 nm films, or blade-coat at 0.5–2 cm/s with substrate at 50–60 °C.
Dry in N2 glovebox 10–20 min.
Post-treatment
Thermal anneal 100 °C for 10 min (optimize 80–120 °C depending on donor).
Alternatively, brief solvent-vapor anneal in CB-saturated chamber (1–3 min) for morphology tuning.
Top electrode
Thermally evaporate MoOx (5–10 nm) and Ag (80–120 nm) for inverted stacks; maintain base pressure < 5×10⁻⁶ mbar.
Characterization
Measure UV–Vis of films, J–V under AM1.5G, and EQE; adjust solvent/additive/anneal as needed.
Note: Parameters are general literature starting points, not item-specific guarantees. Follow your facility’s safety and processing SOPs.
Biological Roles
O-IDTBR is an engineered organic semiconductor intended for materials science research. It has no established biological role, metabolic function, or involvement in cellular signaling.
Not a nutrient, enzyme substrate, or receptor ligand.
Insoluble in aqueous media; not designed for biocompatibility or bioavailability.
Any use in biological contexts should be limited to physical interfacing studies (e.g., optoelectronic biointerfaces) under appropriate safety and compatibility assessments. No medical or clinical applications are implied.
Buffer Applications
Not typically applicable. O-IDTBR is hydrophobic and insoluble in water and standard biological buffers; it is used in organic solvent systems for thin-film deposition. For relevant guidance, refer instead to Solvent Selection, Reaction & Applications, and Application Protocols.
Green Alternatives
Processing O-IDTBR traditionally relies on chlorinated solvents for solubility and film quality. Greener strategies (literature/general) aim to replace these with less hazardous solvents while maintaining device metrics.
Comparison (general guidance):
Chlorinated vs non-chlorinated systems:
Chlorobenzene (CB), o-dichlorobenzene (o-DCB): Excellent solubility and drying control; regulatory and EHS burdens are higher.
Toluene, o-xylene, anisole, mesitylene: Lower toxicity and improved sustainability; may require higher temperature, longer drying times, or small additive fractions (e.g., DIO ≤ 1–2%).
Alternative solvent/additive strategies:
Anisole-based inks with gentle heating (60–90 °C) and blade coating can yield competitive morphologies when paired with appropriate donors and interlayers.
Cyclopentyl methyl ether (CPME) or 2-MeTHF can be explored for lab-scale coating; solubility and film uniformity must be verified.
Process optimization for greener routes:
Increase substrate temperature (40–70 °C) and control airflow to emulate the drying kinetics of CB/o-DCB.
Utilize solvent blends (e.g., anisole:o-xylene 1:1) to tune volatility and solvation.
Trade-offs:
Potential need for higher coating temperature and tighter control of ink filtration/aging to avoid large-scale aggregation.
Slightly narrower processing windows may require donor/acceptor ratio re-optimization.
Recommendation: Begin with small-area devices to map the new solvent space before scaling.
Pharmaceutical Uses
Not applicable. O-IDTBR is not used as an active pharmaceutical ingredient or common excipient. It is a specialty organic semiconductor for research in optoelectronic devices (e.g., OPVs, photodiodes). No clinical or therapeutic claims are made or implied.
Physical Properties
Item-specific specifications are not provided for this catalog entry. Consult the CoA/Spec Sheet for definitive values.
Appearance: Not specified for this item; refer to CoA/Spec Sheet.
Melting point (literature/general): Typically a high-melting, dark solid; reported thermal transitions can vary by batch and purity; differential scanning calorimetry (DSC) often shows strong crystallization behavior in the 150–300 °C window, but specific values depend on formulation and are not item-specific here.
Solubility (literature/general):
Good solubility in chlorinated aromatic/alkyl solvents at elevated temperature (e.g., chlorobenzene, o-dichlorobenzene, chloroform) suitable for spin/dip coating.
Moderate solubility in some non-chlorinated aromatic solvents (toluene, o-xylene) depending on temperature and concentration.
Insoluble in water and polar protic solvents.
Optical properties (literature/general):
Strong visible–NIR absorption; solution/film absorption bands typically centered in the 600–750 nm region depending on aggregation and processing.
Thin-film optical bandgap often reported around 1.5–1.7 eV (literature), sensitive to microstructure.
Density, refractive index, logP, and vapor pressure: Not specified for this item; refer to CoA/Spec Sheet.
Processing note (general): Warm solutions (60–110 °C) and controlled cooling can assist dissolution and uniform film casting; always filter hot solutions (e.g., 0.45–0.2 μm PTFE) prior to coating.
Quality & Grades
Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.
What “materials science/OPV grade” typically implies (literature/general):
Controlled metal and ionic impurity levels to mitigate charge trapping and recombination.
Narrow molecular weight distribution (for small molecules: tight control of side-product content and isomeric purity) to ensure reproducible film morphology and device performance.
Low residual solvent and low ash content for cleaner thermal processing.
Stabilizers/additives: Not specified for this item; refer to CoA/Spec Sheet. Most OPV small molecules are supplied neat without stabilizers; if present, the CoA will note any processing aids.
Quality controls commonly applied (general):
NMR (1H/13C), HRMS, and elemental analysis for identity/purity confirmation.
HPLC/UPLC or GPC (for oligomeric content) to quantify related substances.
UV–Vis and photoluminescence profiles for batch-to-batch optical consistency.
DSC/TGA to establish thermal transitions and onset decomposition for processing windows.
Recommendation: Request and review the CoA/Spec Sheet for this exact lot prior to device fabrication. For high-end OPV studies, pre-filtering and optional Soxhlet extraction (e.g., methanol/hexane/CB sequence) may further harmonize film morphology.
Reaction & Applications
This product functions primarily as an optoelectronic material rather than a synthetic reagent. The following summarizes research applications and processing considerations (literature/general):
Primary application: Electron-accepting component in bulk-heterojunction (BHJ) organic solar cells, photodiodes, and photodetectors. O-IDTBR is well-known for compatibility with P3HT and other donor polymers, enabling relatively high open-circuit voltage and red–NIR responsivity.
Device architectures:
Inverted OPV (glass/ITO/ZnO or SnO2/active layer/MoOx/Ag or Al) often yields stable performance.
Conventional OPV (glass/ITO/PEDOT:PSS/active layer/Ca/Al) is also used; ensure careful moisture control.
Blend guidelines (starting points from literature):
Donor:Acceptor mass ratio 1:1 to 1:1.5; total solids 10–25 mg/mL in CB or o-DCB.
Film thickness 80–200 nm; optimize via spin speed or coating gap.
Thermal annealing 80–120 °C for 5–15 min or solvent-vapor annealing to tune phase separation.
Additives and morphology control:
0.5–3 vol% DIO, CN, or NMP have been explored to promote optimal domain sizes and increased crystallinity; confirm compatibility with donor and substrate.
Performance notes (qualitative, literature): O-IDTBR blends can deliver strong external quantum efficiency in the 500–800 nm region; PCE depends on donor system and processing.
For chemical reactivity in synthesis: Not typically employed as a reagent; its conjugated backbone is the final functional material.
Reaction Conditions
As a device material, “reaction conditions” translate to solution preparation and film deposition parameters. The following are literature/general starting points—optimize per donor polymer, substrate, and toolset.
Ink preparation:
Concentration: 10–25 mg/mL total solids (donor + O-IDTBR) in chlorobenzene (CB) or o-dichlorobenzene (o-DCB).
Temperature: Dissolve at 80–110 °C with stirring for 1–3 h; keep warm and protected from light. Filter hot through 0.2–0.45 μm PTFE.
Additives: 0–3 vol% DIO or CN when finer phase separation is needed; validate for your donor system.
Film casting (spin coat example):
Substrates: ITO/ZnO (inverted) or ITO/PEDOT:PSS (conventional), pre-cleaned and UV–ozone treated.
Spin: 1000–3000 rpm, 30–60 s, targeting 80–200 nm active layer.
Post-treatment: Thermal anneal 80–120 °C for 5–15 min; alternatively, brief solvent-vapor annealing can tune crystallinity.
Blade/slot-die coating:
Wet thickness: 50–200 μm depending on solids and viscosity.
Substrate temperature: 40–70 °C to control drying; N2 environment reduces defect density.
Electrode deposition (general): MoOx (5–10 nm) and Ag/Al top electrodes for inverted stacks; Ca/Al for conventional stacks (handle air sensitivity appropriately).
Expected outcomes (qualitative): Smooth films with nanoscale phase separation (10–50 nm) and strong absorption 500–800 nm; device EQE across green–red–NIR.
Note: These are literature-style guidelines, not item-specific specifications. Always perform small-area optimization before scaling.
Safety & Handling
Authoritative safety information must be taken from the product’s SDS. The following is general guidance for small-molecule organic semiconductors.
GHS classification, signal word, pictograms, H-statements: Not specified for this item; refer to SDS.
Likely hazards (general): Combustible organic solid; dust may cause mechanical irritation. Avoid inhalation of dusts/fumes, ingestion, and skin/eye contact.
PPE (general best practice):
Safety glasses or chemical splash goggles; lab coat; disposable nitrile gloves (change regularly); use FFP2/N95 dust mask if handling powders that can become airborne.
Handle solutions in a fume hood to avoid exposure to solvent vapors.
Handling practices:
Minimize dust generation; use antistatic measures when weighing.
Prepare solutions with dry, high-purity solvents; filter before coating to remove particulates.
Protect from light to prevent photochemical degradation of conjugated backbones.
Incompatibilities (general): Strong oxidizers, strong acids/bases under forcing conditions, and halogenating agents. Avoid prolonged exposure to UV light and elevated temperatures in air.
First-aid overview (general):
Inhalation: Move to fresh air; seek medical attention if symptoms persist.
Skin contact: Wash with soap and water; remove contaminated clothing.
Eye contact: Rinse cautiously with water for several minutes; remove contact lenses if present; seek medical advice if irritation continues.
Ingestion: Rinse mouth; do not induce vomiting unless directed by medical personnel.
Fire-fighting (general): Use CO2, dry chemical, or foam; combustion may produce CO/CO2 and sulfur/nitrogen oxides. Firefighters should wear self-contained breathing apparatus.
Always consult the SDS for definitive hazards and response measures.
Solvent Selection
O-IDTBR is typically processed from high-boiling, aromatic or chlorinated solvents to promote dissolution and controlled film formation.
Nonpolar to moderately polar, π-rich solute; favors aromatic solvents.
Good solubility: chlorobenzene (CB), o-dichlorobenzene (o-DCB), chloroform (CF); miscible with solvent additives such as 1,8-diiodooctane (DIO) at low vol%.
Alternative greener solvents explored: toluene, o-xylene, anisole, mesitylene; may require elevated temperature or small amounts of processing additives.
Selection guidance (general):
For blade/spin coating at room temperature: CB and o-DCB give reliable wetting and allow slow evaporation for morphology control.
For slot-die/roll-to-roll: higher-boiling o-DCB or anisole/xylene blends help with drying time control; adjust web temperature and airflow accordingly.
For non-chlorinated processing: start with o-xylene or anisole at 5–15 mg/mL, 60–110 °C dissolution; fine-tune with ≤3 vol% DIO or CN if needed (verify additive compatibility).
Practical tips:
Filter hot solutions (0.45–0.2 μm PTFE) immediately prior to coating to remove particulates/aggregates.
Control solution age; some A–D–A systems slowly aggregate—prepare fresh daily or keep warm and protected from light.
Substrate surface energy matters; UV–ozone and a compact interlayer (e.g., ZnO) aid uniform spreading in inverted OPV stacks.
Note: Optimize solvent systems jointly with donor polymer choice, target thickness, and drying kinetics to achieve desired phase separation (10–50 nm) and crystallinity.
Storage & Reconstitution
Storage conditions (item-specific):
Protected from light, Room temperature (as provided in Product Data).
Shipped: Normal conditions.
Container and atmosphere (general best practice):
Store in amber vials inside a desiccator; keep tightly closed. For long-term storage, a dry inert atmosphere (N2/Ar) is recommended to limit slow oxidative changes.
Handling and solution preparation (general):
Prepare solutions in dry, high-purity solvents (e.g., chlorobenzene, o-dichlorobenzene, chloroform). Warm to 80–110 °C to assist dissolution; stir until fully homogeneous.
Filter solutions (0.2–0.45 μm PTFE) immediately before coating. Protect from light throughout.
If solutions must be stored, keep in amber vials at room temperature or 4 °C, under inert gas; use within 24–72 h to minimize aggregation.
Freeze–thaw guidance: Not applicable to solids; avoid repeated heating–cooling cycles of solutions which may change aggregate state. Prepare fresh as needed.
Stability notes (general): Conjugated small molecules can undergo slow photo-oxidation; limiting oxygen, moisture, and light exposure preserves performance.
For definitive shelf-life and any item-specific limits, consult the CoA/Spec Sheet for this SKU.
Structure & Identity
Brief overview: O-IDTBR is a non-fullerene, fused-ring small-molecule organic semiconductor widely used as an electron acceptor in solution-processed organic photovoltaics (OPVs).
Product identifiers (item-specific):
SKU: O487524
Product Name: O-IDTBR
CAS: 2077945-91-4
Molecular Formula: Not specified for this item; refer to CoA/Spec Sheet.
Molecular Weight: Not specified for this item; refer to CoA/Spec Sheet.
SMILES: Not specified for this item; refer to CoA/Spec Sheet.
InChIKey: Not specified for this item; refer to CoA/Spec Sheet.
Structural features (literature/general description):
Architecture: A–D–A (acceptor–donor–acceptor) small molecule.
End groups: “BR” denotes rhodanine-type electron-withdrawing termini that lower LUMO and promote electron affinity.
Side chains: Alkyl (octyl) substitution on the IDT core (hence “O-”) for solubility and film-forming control.
Conjugation: Fully conjugated backbone with heteroatoms (S, N, O) enabling intra/intermolecular charge transfer.
2D structure described in words (literature/general):
A central rigid, nearly planar fused-ring IDT scaffold flanked by heteroaromatic spacers and terminated by rhodanine carbonyl–thioxo moieties. Long linear alkyl chains (C8) append from the core to modulate aggregation and solubility.
Note: Exact atom count, stereochemistry (typically none), and registry identifiers beyond CAS are not specified for this item and should be taken from the CoA/Spec Sheet or the SDS for definitive identification.
Synthetic Utility
O-IDTBR is a finished small-molecule semiconductor and is not generally employed as a synthetic intermediate or reagent.
Chemical reactivity (general): The conjugated backbone is designed for stability under device-processing conditions; terminal rhodanine-type moieties and the fused-ring core are not typically leveraged for downstream organic synthesis.
Retrosynthetic context (literature/general): Its assembly commonly involves palladium-catalyzed cross-couplings (e.g., Stille/Suzuki) and Knoevenagel-type condensations to append rhodanine end groups—useful to know for troubleshooting impurities but not for subsequent transformations.
Practical implication: Treat O-IDTBR as a performance material; process optimization (solvent, additives, thermal/solvent annealing) is the lever for results, rather than chemical modification in situ.
If derivatization is desired for research, plan de novo synthesis from appropriate IDT cores and end-group building blocks rather than attempting functionalization of the final material.
Target Specificity
Not applicable. This product is not a biochemical probe, antibody, or ligand with defined molecular targets. It functions as an electron-accepting semiconductor in solid-state devices.
Frequently Asked Questions
What is the purity of this product?
This product is supplied at ≥98% purity (chemical assay). Lot-specific values are stated on the Certificate of Analysis.
How is this product shipped?
This product ships under standard ambient conditions. No temperature-controlled packaging is required.
How should this product be stored?
Store at room temperature, protected from light. The material is light-sensitive — keep it in its original opaque or amber container.
What are the CAS number, molecular formula and molecular weight?
The CAS Number is 2077945-91-4, the molecular formula is C72H88N6O2S8, and the molecular weight is 1326.03 g/mol.
What documentation is provided?
Available product documentation, including Certificates of Analysis (COA), Safety Data Sheets (SDS), and specification sheets, is shown in the product document area. Document availability and access follow the current site policy.
We use cookies to ensure the website functions properly and, where permitted, to improve your experience. You can manage your preferences at any time in Settings. Learn more in our Cookie Policy.
Shall we send you a message when we have discounts available?
Remind me later
Thank you! Please check your email inbox to confirm.
Products are supplied to verified businesses, institutions, and qualified professionals for research and development use only. Not for use in humans, animals, diagnosis, or therapy.