Dodecanethiol functionalized gold nanoparticles - 0.6-0.9% solid material basis, 0.01% HAuCl₄ in toluene

Cat. No.: D466047
주문 가능
등급 & 순도 0.6-0.9% solid material basis, 0.01% HAuCl₄ in toluene
Synonyms
Dodecylthiol functionalized gold nanoparticles
Storage
Room temperature
★
크기
USA
독일 (EU)*
가격
수량
10ml
D466047-10ml
주문제작 · 8~12주
US$319.90
Enter a quantity for the sizes you want to add.

개요

Description

Useful for the self-assembly of gold monolayers for nanoelectronics.

사양

동의어
Dodecylthiol functionalized gold nanoparticles
사양 및 순도
0.6-0.9% solid material basis, 0.01% HAuCl₄ in toluene
보관 조건
Room temperature

고급 데이터

인증서(CoA, COO, BSE/TSE 및 분석 차트)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:
자주 묻는 질문과 기사
솔루션 계산기
리뷰

고객 리뷰

Application Protocols

General, non-item-specific procedures (literature-informed). Adjust to your batch’s concentration/solvent as stated on the CoA.

  1. Redispersion from dry solid
  • Add a nonpolar solvent (e.g., toluene or heptane) to achieve 1–5 mg/mL.
  • Vortex briefly and sonicate in a water bath for 2–3 minutes until a uniform dispersion is obtained.
  • Optionally pass through a 0.2 µm PTFE syringe filter to remove dust/aggregates.
  1. Place-exchange to carboxylate-terminated ligands (example)
  • Dissolve AuNPs in chloroform (~1 mg/mL). Add 11-mercaptoundecanoic acid (5–20 equiv versus estimated surface sites) and 1–2 equiv triethylamine.
  • Stir at 40 °C for 6–16 h under nitrogen. Monitor by FTIR (C=O ~1710 cm⁻¹) and UV–Vis (minor LSPR shifts).
  • Precipitate with excess ethanol, centrifuge, decant, and redissolve in appropriate solvent. Repeat twice to remove free ligand.
  1. Spin-coated film preparation
  • Disperse particles at 2–5 mg/mL in toluene/anisole (3:1). Filter (0.2 µm PTFE).
  • Spin at 1500 rpm for 45 s onto OTS-treated Si or glass. Dry under nitrogen, then bake at 120 °C for 10 min to remove residual solvent.
  1. Thermal sintering for conductivity (substrate permitting)
  • Ramp to 200–250 °C under nitrogen for 20–30 min; optionally brief air bake at 250 °C for 5 min to remove carbonaceous residues. Verify sheet resistance by four-point probe.

Note: These are example workflows; tailor conditions to your substrate, patterning method, and EHS constraints.

Biological Roles

This product is engineered for materials science and nanofabrication; it is not intended for biological use. No inherent biological roles are assigned to dodecanethiol-functionalized AuNPs.

General literature context (for researchers exploring biointerfaces under controlled laboratory settings):

  • Surface chemistry:
    • The C12 alkanethiolate shell is hydrophobic and typically resists aqueous dispersion and many biomolecular interactions without additional surfactants or ligand exchange. Protein adsorption is reduced compared to charged/hydrophilic shells but can occur via hydrophobic interactions.
  • Transformations for bio-compatibility (not part of this item):
    • Ligand exchange to introduce hydrophilic/charged groups (e.g., PEG-thiols, carboxyl- or amine-terminated thiols) can render AuNPs water-dispersible and enable bioconjugation chemistries.
  • Cellular interactions (literature, general):
    • Uptake and cytotoxicity of AuNPs depend strongly on size, charge, and surface functionality. Hydrophobic, alkyl-terminated particles often aggregate in biological media and are generally unsuitable for direct biological exposure without surfactants or further modification.

Important: The present item is for research use only and not for use in diagnostics, therapeutics, or any in vivo applications.

Buffer Applications

Not typically applicable. Hydrophobically capped dodecanethiol–AuNPs are not designed for aqueous buffer systems and generally do not disperse in standard laboratory buffers (PBS, Tris, HEPES) without surfactants or prior ligand exchange. For buffer-based work, consider water-dispersible AuNPs or perform place-exchange to hydrophilic thiols.

Green Alternatives

Greener choices focus on solvent replacement and lifecycle considerations; the core chemistry (Au–S) is largely fixed.

  • Solvent alternatives (literature/green chemistry perspective):
    • Replace chlorinated aromatics (chloroform, DCM) and toluene with:
      • Cyclopentyl methyl ether (CPME): low peroxide tendency, hydrophobic, good solvency, recyclable.
      • Anisole: lower toxicity than toluene; good film-forming properties.
      • Isopropyl acetate or ethyl acetate: more benign esters; may require co-solvent to maintain stability.
      • Heptane in place of hexane to reduce n-hexane neurotoxicity concerns.
  • Process improvements:
    • Use closed-loop solvent recovery during film casting/ink printing.
    • Photonic/laser sintering to minimize thermal budgets and energy use versus long oven bakes.
  • Alternative materials strategies:
    • For aqueous and bio-oriented work, consider citrate- or PEG-stabilized AuNPs (water-dispersible) to avoid chlorinated solvent use; note different surface chemistry and application windows.

Comparison (general):

  • Toluene vs Anisole: similar solvency; anisole has higher boiling point (154 °C) aiding uniform films; typically lower hazard rating.
  • Chloroform vs CPME: CPME avoids chlorinated waste, has favorable safety profile, but may solvate less strongly; minor sonication can compensate.
  • Hexane vs Heptane: comparable dispersibility; heptane has lower toxicity classification and slightly higher bp aiding film control.

These recommendations are general literature-based tradeoffs and do not alter item-specific specifications (none provided here). Evaluate nanoparticle stability in any new solvent before scale-up.

Pharmaceutical Uses

Not typically applicable to this hydrophobic, materials-focused nanomaterial. Dodecanethiol–AuNPs are not pharmaceutical excipients and are not intended for formulation in drug products.

General industry context (literature):

  • In formulation science research, AuNPs can serve as model fillers for studying rheology of inks/coatings or as conductive elements post-sintering. For biomedical formulation studies, water-dispersible and biocompatible coatings (e.g., PEG) are typically required, which differ fundamentally from the current product.

Note: For research use only; not for human or animal therapeutic or diagnostic use.

Physical Properties

Item-specific physicochemical specifications (e.g., particle size, dispersant/solvent, concentration, plasmon peak, polydispersity, organic content) are Not specified for this item; refer to CoA/Spec Sheet.

General/literature characteristics of dodecanethiol-capped AuNPs:

  • Physical state: typically a stable dispersion in nonpolar organic solvents or a dry black/brown powder if solvent removed.
  • Solubility/Dispersibility (literature):
    • Good in nonpolar or moderately polar aprotic solvents (hexane, heptane, toluene, xylene, chloroform, dichloromethane, THF). Dispersibility improves with gentle sonication.
    • Poor to insoluble in water and polar protic solvents (methanol, ethanol) due to hydrophobic C12 shell.
  • Optical property (literature): localized surface plasmon resonance (LSPR) band for small spherical AuNPs commonly near 510–540 nm in toluene/chloroform; exact position depends on core diameter, ligand, and medium refractive index.
  • Thermal behavior (literature): organic shell decomposes/pyrolyzes on heating (>200–300 °C in inert/air), enabling sintering of Au cores at comparatively low temperatures; precise onset depends on ligand coverage and atmosphere.
  • Density (reference): bulk gold 19.3 g/cm³ (literature); effective density of ligand-coated particles in dispersion is much lower and medium-dependent.
  • Refractive index sensitivity (literature): LSPR peak red-shifts with increasing solvent refractive index and with interparticle coupling (aggregation).

Note: The above values are provided as general literature expectations for alkanethiolate–AuNP systems and are not item-specific specifications.

Quality and Grades
  • Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.

Context and expectations for nanoparticle product quality (general guidance):

  • Typical quality metrics for dodecanethiol–AuNPs include:
    • Core diameter and distribution (TEM/HAADF-STEM) and hydrodynamic size (DLS); polydispersity index (PDI).
    • Concentration of Au (ICP-OES/ICP-MS) and total solids; organic content and ligand:Au ratio (TGA/elemental analysis).
    • Surface chemistry verification (XPS/S 2p, Au 4f; FTIR C–H stretches; thermodesorption MS); absence of free thiol (GC/LC) if relevant.
    • Optical quality (UV–Vis LSPR peak position and full-width at half-maximum, indicating dispersion and size distribution).
  • Grades and what they imply:
    • “Materials research grade” often denotes high colloidal stability and narrow size distributions appropriate for thin films/self-assembly.
    • If “electronic ink grade,” low residual ionic contaminants and optimized organic fraction for low-temperature sintering are typical.
    • Absence/presence of stabilizers beyond dodecanethiol (e.g., additional surfactants) should be disclosed on the CoA.
  • Batch-to-batch considerations:
    • Nanoparticle ensembles may exhibit slight variations in LSPR and size; rely on CoA for batch-specific metrics.
    • Storage solvent, concentration, and any additives (antioxidants, inhibitors) should be reported on the CoA; none are specified here.
Reaction and Applications

Applications (materials science focus; general literature guidance):

  • Thin films and assemblies:
    • Formation of ordered monolayers/multilayers via drop-casting, spin coating, dip-coating, or Langmuir–Blodgett techniques onto hydrophobic substrates. Inter-particle spacing governed by C12 shell thickness provides electron tunneling barriers for nanoelectronic studies.
  • Nanocomposites and inks:
    • Incorporation into polymer matrices (e.g., PS, PMMA, epoxy) to tailor electrical/thermal properties. As sinterable conductive inks/pastes for printed electronics; low-temperature thermal or photonic sintering removes ligands enabling conductive pathways.
  • Surface chemistry platform:
    • Place-exchange (ligand exchange) with incoming thiols/disulfides to introduce functional handles (e.g., carboxyl, amine, azide) for subsequent coupling. Useful for biosensor prototypes after hydrophilization (though this specific product is hydrophobic as supplied).
  • Plasmonics and optics:
    • Size-dependent LSPR for optical materials, refractive index sensing, and metamaterial building blocks. Controlled aggregation (via dithiols) creates plasmonic coupling for SERS substrates; note the C12 shell is insulating and can dampen hotspot accessibility.
  • Catalysis (considerations):
    • As-made hydrophobic shells limit substrate access; catalytic activity may require partial ligand removal or thermal treatment to expose surfaces.

Practical tips:

  • Maintain rigorously clean glassware to prevent unintended ligand exchange; avoid prolonged exposure to nucleophiles that can strip thiols.
  • For film uniformity, control evaporation rate and substrate surface energy; small additions of high-boiling co-solvents (e.g., anisole) can improve leveling (literature practice).
Reaction Conditions

General literature guidance for common operations with dodecanethiol–AuNPs (not item-specific specifications):

  • Redispersion and processing:
    • Concentrations: prepare working dispersions typically 0.1–10 mg/mL in toluene, chloroform, or heptane. Sonicate in a bath for 1–5 minutes; avoid overheating.
    • Film deposition: spin coat at 500–3000 rpm for 30–60 s; adjust viscosity with solvent blends (e.g., toluene/anisole). Dry under ambient or mild vacuum.
  • Ligand place-exchange:
    • Solvent: chloroform, toluene, or THF.
    • Reagents: incoming thiol (1–100 equiv relative to estimated surface sites); base (optional, e.g., triethylamine) for acidic thiols.
    • Temperature/time: 20–60 °C for 2–24 h with stirring; monitor by FTIR/XPS/UV–Vis.
    • Workup: precipitate with ethanol or acetonitrile; centrifuge; redissolve in nonpolar solvent; repeat if needed.
  • Crosslinking/assembly with dithiols:
    • Add ≤1–10 mol% dithiol relative to surface sites; brief sonication; observe controlled LSPR red-shift indicating coupling. Excess leads to gelation/precipitation.
  • Thermal/photonic sintering (for conductive features):
    • Thermal: 150–300 °C for 10–60 min (substrate-limited). Photonic: millisecond xenon flash or laser pulses; optimize fluence to remove organics without damaging substrate. Residual carbon can be minimized by oxidative post-bakes.

Expected outcomes (literature):

  • Successful exchange shifts FTIR (appearance of new headgroup bands), XPS S 2p binding energy changes, and subtle LSPR shifts. Sintering causes LSPR loss and DC conductivity increase.
Safety and Handling

Item-specific GHS classification, signal word, pictograms, and H-statements: Not specified for this item; refer to SDS.

General safety guidance for handling alkanethiol-functionalized AuNPs:

  • Hazards (literature/experience):
    • Nanoparticles may present inhalation hazards; avoid aerosolization and dust. Hydrophobic organic dispersions are flammable depending on solvent.
    • Thiolate ligands and residual free thiols can be irritants; strong odors may occur with free thiols.
  • PPE and engineering controls:
    • Use gloves, lab coat, and splash goggles. Work in a fume hood when transferring powders or volatile organic dispersions; use a particulate-rated respirator if aerosol risk exists as dictated by risk assessment.
  • Incompatibilities and reactivity (general):
    • Strong oxidizers; aqua regia and halogenated oxidants dissolve/etch Au. Cyanide forms soluble Au complexes (extremely hazardous—do not use without specialized facilities). Peroxides in ethers may oxidize ligands.
    • Avoid prolonged UV/ozone or plasma unless intentionally removing ligands.
  • First aid (overview, non-exhaustive):
    • Inhalation: move to fresh air, seek medical attention if symptoms persist.
    • Skin/eye contact: wash with soap/water; rinse eyes with water for 15 minutes; remove contaminated clothing.
    • Ingestion: rinse mouth; do not induce vomiting; seek medical advice.
  • Spill and waste:
    • Absorb organic dispersions with inert material; collect as hazardous waste. Dispose of nanoparticle-containing waste as regulated chemical waste; prevent release to drains.

Always consult the product SDS and your institutional EHS policies for authoritative safety information.

Solvent Selection

Dodecanethiol capping renders the AuNP surface hydrophobic; dispersibility follows the solvent’s nonpolarity and ability to solvate alkyl chains.

  • Preferred solvents (literature/guidance):
    • Excellent: hexane, heptane, toluene/xylene, cyclohexane, chloroform, dichloromethane.
    • Good: THF, diethyl ether, tert-butyl methyl ether (TBME), anisole, isopropyl acetate.
    • Poor: alcohols (MeOH, EtOH), acetonitrile; Water: typically insoluble without additional amphiphiles.
  • Practical tips:
    • Start with toluene or chloroform for film fabrication and spectroscopy (good balance of volatility and solvation), or hexane/heptane for nonpolar processing and precipitation steps.
    • Gentle bath sonication and brief vortexing aid redispersion from dried solids; avoid high-power probe sonication that can induce ligand desorption or heating.
  • Small comparison (literature values):
    • Hexane (ε ≈ 1.9): fast-evaporating, low solvency—good for precipitation and quick-drying coatings; may promote aggregation at high solids.
    • Toluene (ε ≈ 2.4): higher solvency; slower evaporation for uniform films.
    • Chloroform (ε ≈ 4.8): strong solvency; rapid drying; handle with care for toxicity.
    • THF (ε ≈ 7.6): miscible with many organics; can pick up peroxides; store dry.
  • When to choose alternatives:
    • For greener processing, consider CPME or anisole in place of toluene/chloroform; for aqueous systems, perform ligand exchange to hydrophilic thiols or use citrate-stabilized AuNPs instead.
Storage and Reconstitution
  • Storage conditions (item-specific): Room temperature (per Product Data). If supplied as a dispersion, keep the container tightly sealed to minimize solvent loss. If supplied as a dry solid, store in a closed vial to prevent dust and moisture ingress.
  • Light/air exposure: Store away from strong UV light and heat sources. Normal laboratory air is acceptable; prolonged exposure to ozone/UV can oxidize or strip ligands.
  • Freezing: Avoid freezing of organic dispersions; phase separation and aggregation may occur.
  • Reconstitution (general):
    • To prepare working dispersions, add an appropriate nonpolar solvent (e.g., toluene, heptane, chloroform) to the vial to the desired concentration. Vortex and bath-sonicate briefly (1–5 minutes) until homogeneous. Filter through 0.2 µm PTFE if needed.
  • Stability (general expectations):
    • Hydrophobically capped AuNPs are typically stable for months at ambient conditions if kept dry and protected from solvent evaporation. In dispersion, gradual solvent loss can concentrate samples and promote aggregation; periodically check LSPR in UV–Vis for signs of aggregation (peak broadening/red-shift).
  • Shipping: Not specified for this item; refer to CoA/Spec Sheet. Typically shipped at ambient temperature for hydrophobic AuNPs in compatible packaging.
  • Handling notes:
    • Minimize headspace to reduce solvent evaporation. If concentration drifts, restore volume with fresh solvent and sonicate gently. Do not use strong oxidants or halogenating agents in storage areas.

For definitive stability window, shelf life, and any additives/stabilizers, consult the product CoA and SDS.

Structure and Identity

Dodecanethiol-functionalized gold nanoparticles (AuNPs) are metal nanocrystals with a covalently chemisorbed self-assembled monolayer (SAM) of 1-dodecanethiol on the surface.

  • Item-specific identifiers:
    • CAS: Not specified for this item; refer to CoA/Spec Sheet.
    • InChIKey / SMILES: Not applicable to nanomaterials comprised of a metallic core with a mixed-atom surface; no single molecular descriptor.
    • Molecular Formula / Molecular Weight: Not applicable for polydisperse nanoparticle ensembles.
  • Structural features (general, literature):
    • Core: crystalline Au(0), typically face-centered cubic (fcc).
    • Ligand shell: densely packed alkanethiolate (–S–Au) SAM from 1-dodecanethiol (CH3–(CH2)11–SH); the S–H bond is cleaved upon binding, forming Au–S chemisorption.
    • Overall construct: a metallic nanocore (diameter typically a few to tens of nm in common preparations; exact size Not specified for this item) surrounded by a hydrophobic C12 organic monolayer providing steric stabilization in nonpolar media.
  • 2D description in words:
    • A central spherical gold particle whose surface atoms are each coordinated to sulfur headgroups; outward from the surface radiate densely packed, all-trans alkyl chains (12 carbons) forming a hydrophobic brush. The outermost interface is methyl-terminated, imparting nonpolar character and low surface energy.
  • Category: Materials science nanomaterial (hydrophobically stabilized AuNPs).
  • Notes on identity testing (general): transmission electron microscopy (TEM) for core size/crystallinity, thermogravimetric analysis (TGA) for organic content, X-ray photoelectron spectroscopy (XPS) for Au–S bonding, UV–Vis for plasmon resonance position (size-dependent).
Synthetic Utility

While not a molecular reagent, dodecanethiol–AuNPs function as nanoscale building blocks and reactive surfaces in synthetic nanofabrication.

  • Surface functionalization (general literature):
    • Place-exchange reactions: incoming thiols/disulfides can substitute into the ligand shell, enabling installation of functional groups (–CO2H, –NH2, –N3, –SH spacers) with tunable exchange extents. Kinetics depend on ligand chain length, solvent, temperature, and initial coverage.
    • Crosslinking: α,ω-dithiols or multithiols create interparticle networks and gels; useful for constructing films or 3D frameworks with controlled porosity and interparticle spacing.
  • Processing transformations:
    • Thermal/photonic ligand removal to sinter particles into continuous Au features for conductive traces and contacts. C12 length balances colloidal stability with relatively low-temperature removal compared to longer chains.
    • Seed utility: organic-phase Au seeds can be overgrown to larger particles/nanorods in nonaqueous media (literature methods), with the C12 shell influencing facet development.
  • Interfacial assembly:
    • Langmuir–Blodgett and self-assembly at liquid–liquid interfaces afford ordered arrays; useful for metamaterials, optical gratings, and tunneling junction studies.

Notes:

  • Control atmosphere (air vs inert) during thermal steps to tune organic removal pathways.
  • For chemoselective patterning, exploit differences in ligand affinity (thiols > amines > phosphines on Au) and use maskable exchange protocols.
Target Specificity

Not applicable. This product is not a biological targeting reagent (e.g., antibody, aptamer) and has no defined antigen/epitope specificity.

Shall we send you a message when we have discounts available?

Remind me later

Thank you! Please check your email inbox to confirm.

Oops! Notifications are disabled.