Biotin-labeled EMSA probe-STAT3 - 0.2μM

Cat. No.: B752135
DISPONIBLE À COMMANDE
QUALITÉ & PURETÉ 0.2μM
Storage
Store at -20°C
Shipped In
Ice chest + Ice pads
★
Taille
Allemagne (EU)
USA*
Prix
Qté
200μl
B752135-200μl
Sur commande · 8–12 semaines
190,82€
Enter a quantity for the sizes you want to add.

Vue d’ensemble

Aladdin's Biotin-labeled EMSA Probe - STAT3 (0.2μM) is a STAT3 consensus oligonucleotide designed for EMSA . This double-stranded oligonucleotide contains the well-recognized binding sequence for STAT3 transcription factors, and can be used as a probe for EMSA. The nucleotide sequence of STAT3 consensus oligo is as follows


Precautions:

Avoid heating above 40℃, as double-stranded DNA probe will be denatured at high temperatures into single strands that cannot be used in EMSA.This product is for R&D only. Not for drug, household, or other uses.For your safety and health, please wear a lab coat and disposable gloves during the operation.


Instructions for Use:

1.EMSA binding reactiona.Set up the following reactions by adding the reagents in sequence. Negative Control Reactions: Nuclease-Free Water7-7.5μlEMSA/Gel-Shift Binding Buffer (5X)2μlNuclear Protein or Purified Transcription Factor0μlBiotin-labeled Probe0.5-1μlTotal Volume10μlSample Reaction:Nuclease-Free Water5-5.5μlEMSA/Gel-Shift Binding Buffer (5X)2μlNuclear Protein or Purified Transcription Factor2μlBiotin-labeled Probe0.5-1μlTotal Volume 10μlCold Probe Competition Reaction:Nuclease-Free Water4-4.5μlEMSA/Gel-Shift Binding Buffer (5X)2μlNuclear Protein or Purified Transcription Factor2μlUnlabeled Probe1μlBiotin-labeled Probe0.5-1μlTotal Volume 10μlCold Mutant Probe Competition Reaction: Nuclease-Free Water4-4.5μlEMSA/Gel-Shift Binding Buffer (5X)2μlNuclear Protein or Purified Transcription Factor2μlUnlabeled Probe1μlBiotin-labeled Probe0.5-1μlTotal Volume10μlSuper-shift Reaction:Nuclease-Free Water4-4.5μlEMSA/Gel-Shift Binding Buffer (5X)2μlNuclear Protein or Purified Transcription Factor2μlTarget Protein Specific Antibody1μlBiotin-labeled Probe0.5-1μlTotal Volume10μlNote 1: The recommended dosage of biotin-labeled EMSA probe is 0.5µl per reaction. If the EMSA bands of target proteins are weak, the dosage of biotin-labeled EMSA probe can be increased to 0.75 µl or 1 µl as appropriate. Note 2: For cold probe competition, the recommended amount of unlabeled probe is 50-100 times that of biotin-labeled probe, but can be adjusted as required.b.Before adding the labeled probe, the reaction mix should be mixed well and incubated at room temperature (20-25℃) for 10 minutes to eliminate possible non-specific binding between probes and proteins. Otherwise allow cold probes react preferentially. Then add the labeled probe, mix well and incubate at room temperature (20-25℃) for 20 minutes.c.Add 1μl of EMSA/Gel-Shift Loading Buffer (colorless, 10X) into each reaction and load onto gel immediately after mixing. Note: Sometimes bromophenol blue can affect protein-DNA interactions. It is recommended to use the colorless EMSA/Gel-Shift Loading Buffer, or that including a very small amount of blue loading buffer to make observation easier.2.For detailed EMSA procedures with the biotin-labeled probes, please refer to the manual of ’s Chemiluminescent EMSA Kit .


Spécifications

Spécifications et pureté
0.2μM
Stabilité et stockage
Store at -20℃ for up to 1 year.
Conditions de stockage de stockage
Store at -20°C
Expédié en
Ice chest + Ice pads
Ce produit nécessite l'expédition en chaîne froide. Les services terrestres et autres services économiques ne sont pas disponibles.
Product Line
B752135-200μl

Données avancées

Certificats (CoA, COO, BSE/TSE et tableau d'analyse)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:
Calculateurs de solution
Avis

Avis des clients

Foire aux questions

How should this product be stored?
Store at ?20 °C. Freezer storage is required to maintain the specified shelf life.
How is this product shipped?
This product ships in an insulated container with ice pads. Unpack on arrival and transfer it to the storage condition stated above.
What documentation is provided?
Available product documentation, including Certificates of Analysis (COA), Safety Data Sheets (SDS), and specification sheets, is shown in the product document area. Document availability and access follow the current site policy.

Souhaitez-vous que nous vous envoyions un message lorsque des réductions seront disponibles?

Me rappeler plus tard

Merci ! Veuillez vérifier votre boîte de réception e-mail pour confirmer.

Oups ! Les notifications sont désactivées.