BioReagent BioReagent for sensitive chromatographic and analytical workflows requiring minimal baseline interference.
Store at 2-8°C,Do not freeze Ships Wet ice,Do not freeze Check lot-specific COA for exact specifications.
SDS, COA, datasheet, and spec sheet available for download. Lot-specific COA accessible via lot number lookup.
Cited in 0 peer-reviewed publications across chromatography, organic synthesis, and cross-coupling reactions.
Human CD3⁺ Cell Removal Beads are generated by covalently coupling anti‑human CD3 antibody to magnetic beads. They can be used for rapid and efficient removal of CD3⁺ cells from human peripheral blood mononuclear cells (PBMCs) or from red blood cell‑lysed human peripheral blood white blood cells (WBCs).
Applications
Removal of CD3⁺ cells from human PBMCs or WBCs.
|
Protocol
When the sample is PBMC or WBC:
Prepare single‑cell suspension
Count the obtained human PBMCs or human WBCs. Resuspend 1×10⁸ cells in 450 μL of Isolation Buffer.
Note: Isolation buffer is PBS containing 2 mM EDTA and 2% fetal bovine serum (FBS). FBS may be replaced with 0.5% BSA or HSA. The buffer must be pre‑filtered through a 0.22 μm filter.
Incubate cells with beads
Add the 450 μL cell suspension prepared in step 1 to the bottom of a 1.5 mL centrifuge tube. Then add 50 μL of washed and resuspended Human CD3⁺ Cell Removal Beads (the beads must be washed before use: select a pipette with an appropriate volume range, thoroughly resuspend the beads by pipetting, avoiding bubbles. Transfer the required volume of beads to a 1.5 mL centrifuge tube, add 1 mL of Isolation Buffer, centrifuge at 10,000 g for 1 min or use a magnetic separator for 3 min, then discard the supernatant. Add 1 mL of Isolation Buffer, wash the beads once more, and then resuspend the beads in the same volume of Isolation Buffer as originally taken. For example, if 50 μL of beads are taken, resuspend them in 50 μL of Isolation Buffer after washing). Mix the liquid in the tube by pipetting, and incubate at room temperature for 30 min using a rotator.
Note: For other cell numbers, adjust the cell volume and the amount of Human CD3⁺ Cell Removal Beads proportionally. For fewer than 5×10⁷ cells, adjust the cell suspension volume to 225 μL and add 25 μL of Human CD3⁺ Cell Removal Beads.
Magnetic separation
After incubation, add Isolation Buffer to bring the total volume to 3 mL (the liquid can be transferred from the 1.5 mL centrifuge tube to a FACS tube in several steps). Mix thoroughly by pipetting up and down 10 times (avoid vigorous shaking or inverting). Then place the FACS tube on a magnetic separator and let stand for 5 min.
Collect target cells
After magnetic separation, the target cells are in the supernatant. Carefully collect the supernatant (avoid taking up any beads), centrifuge at 500 g for 5 min, discard the supernatant, and collect the cells.
Resuspend for further use
Wash the cells if required for your experiment, or centrifuge and resuspend them in the desired buffer or culture medium for subsequent molecular or cell biology experiments.
Removal Performance
CD3⁺ cells were removed from human WBCs and human PBMCs. Cells before and after removal were stained with APC anti‑human CD3 antibody (clone OKT3) and PE anti‑human CD4 antibody (clone RPA‑T4) and analyzed by flow cytometry. The results are as follows:
WBCs: CD3⁺ cell purity before and after removal was 16.39% (mean±SD: 19.34%±4.16%) and 0.1% (mean±SD: 0.075%±0.04%), respectively.
PBMCs: CD3⁺ cell purity before and after removal was 53% (mean±SD: 47.51%±9.67%) and 0.28% (mean±SD: 0.42%±0.25%), respectively.
.png?access_token=981600a7-0642-409b-a1b3-4a1147305c91)
.png?access_token=57a0c5a1-e015-443b-a3a2-72334597a11c)
Precautions
Avoid freezing the beads during use and storage.
Low‑retention pipette tips and centrifuge tubes are recommended to avoid loss of beads due to adsorption.
Before taking the beads, select a pipette with an appropriate volume range, thoroughly resuspend the beads by pipetting, and avoid generating bubbles during pipetting.
For research use only.
Comprehensive hazard, handling, storage, and regulatory compliance document.
Download SDS →Lot-specific quality data. Enter your lot number to retrieve the exact COA.
Look up COA →Full quality attributes and acceptance criteria for this grade.
View spec sheet →Find and download the COA for your product by matching the lot number on the packaging.
| Lot Number | Certificate Type | Datum | Artikel |
|---|---|---|---|
 ZJ26F0737979 | Certificate of Analysis | Jul 31, 2026 | R1522426 |
Our grade selection guide covers purity, stabilizer status, and application suitability for all variants in our catalog.
View BioReagent grade guide →