m-PEG5-triethoxysilane is a PEG derivative containing a triethoxysilane moiety which is commonly used for surface modification. The hydrophilic PEG linker increases the water solubility of a compound in aqueous media. The water solubility of the PEG chain is enhanced with longer PEG chains.
Spezifikationen
Spezifikationen & Reinheit
≥98%
Storage
Store at -20°C
Verschickt in
Ice chest + Ice pads
Dieses Produkt erfordert Kühlkettenversand. Grundversand und andere Economy-Optionen sind nicht verfügbar.
Reinheit
≥98%
Namen und Kennungen
Molekulargewicht
483.7
Erweiterte Daten
Zertifikate (CoA, COO, BSE/TSE und Analyse-Diagramm)
C of A & Other Certificates(BSE/TSE, COO):
Analytical Chart:
Lösungsrechner
Molarity Calculator
Determine the necessary mass, volume, or concentration for preparing a solution.
Dilution Calculator
Determine the dilution needed to prepare a stock solution.
Reconstitution Calculator
Bewertungen
Kundenbewertungen
Application Protocols
Example protocol (general literature guidance; adjust to substrate and facility SOPs):
Glass coverslip PEG–silane passivation
Clean coverslips by oxygen plasma (5–10 min) or piranha (use extreme caution). Rinse thoroughly with water and dry at 120°C for 15–30 min.
Prepare 1% v/v m-PEG5-triethoxysilane in anhydrous toluene (optional: add 0.1% acetic acid for very mild catalysis only if moisture is stringently controlled).
Immerse coverslips for 60 min at room temperature with gentle agitation in a dry environment.
Rinse sequentially with dry toluene, dry ethanol, then blow dry with nitrogen.
Cure at 110–120°C for 30–60 min to promote siloxane crosslinking.
Store treated slides in a desiccator until use.
Alternative aqueous-alcohol approach
Mix ethanol/water (95:5 v/v), adjust to pH ~5 with acetic acid. Add silane to 0.5–1% v/v and allow 10–15 min pre-hydrolysis.
Immerse activated glass 10–30 min at room temperature.
Rinse ethanol → water → ethanol; dry with nitrogen and cure 100–110°C for 30 min.
Notes
Perform small pilot tests to optimize concentration/time for uniform films.
Co-deposit with 0.01–0.2% of a functional silane (e.g., aminosilane) when partial reactivity is desired while retaining PEG passivation.
Biological Roles
This product is a surface-coupling reagent rather than a biomolecule; intrinsic biological roles are not applicable.
General/literature perspective
Poly(ethylene glycol) chains are widely used to impart “stealth” characteristics by reducing protein adsorption and cell adhesion on surfaces through entropic and hydration-layer effects.
Methoxy-capped PEG (mPEG) presents a non-reactive, hydrophilic terminus, minimizing undesired bioconjugation while maintaining resistance to biofouling.
On biosensor and diagnostic platforms, PEGylated silane layers can improve signal-to-noise by suppressing nonspecific binding of serum proteins.
No endogenous metabolic or signaling functions are associated with this reagent; benefits arise from surface physics and interfacial chemistry rather than biological activity.
Research use only
As noted in Product Data: For research use only. Not for use in humans or clinical applications.
Buffer Applications
Not a buffering reagent.
Practical context (general)
In aqueous silanization workflows, mildly acidic buffers (e.g., 5–20 mM acetic acid or acetate buffer, pH ~4.5–5.5) are commonly used to pre-hydrolyze the triethoxysilane prior to substrate deposition.
After deposition, extensive rinsing with the same alcohol/water vehicle and finally with water (or buffer relevant to downstream bioassay) is recommended.
Avoid strong bases or high-pH buffers during silanization as they can induce rapid condensation/polymerization and rough films.
Green Alternatives
Greener process considerations (general)
Solvent choice has the largest environmental impact for silanization. Replacing chlorinated or aromatic solvents with bio-derived or lower-toxicity options can reduce footprint.
Comparison (general guidance)
Conventional vs greener for silanization
Toluene (anhydrous): excellent control; high VOC and aromatic content.
DCM: effective, fast wetting; chlorinated solvent with significant environmental/health concerns.
THF: good solvency; peroxide formation risk; typically petro-derived.
Ethanol/water (pH ~4.5–5): renewable, low-toxicity; accelerates hydrolysis—requires careful control to avoid polymerization and ensure uniform films.
2-MeTHF or CPME: greener ethers with lower toxicity and often bio-based; provide anhydrous media with reduced peroxide tendency versus THF (CPME) and better safety margins.
Trade-offs
Aqueous alcohol routes may produce thicker, more crosslinked layers and require stringent rinse/cure steps to avoid haze.
Non-aqueous greener ethers may slightly alter deposition kinetics; small pilot studies are recommended.
Use minimal effective silane concentration (e.g., 0.5–1% v/v) and recover solvents where possible to reduce waste.
Waste and EHS
Hydrolysis releases ethanol—a relatively benign byproduct—but siloxane residues can foul drains; collect and dispose as organic waste.
Prefer closed systems or vapor-phase methods to reduce VOC emissions.
Pharmaceutical Uses
No direct pharmaceutical or excipient designation is provided for this item.
General materials role in pharma/bioprocess settings (non-clinical)
Surface passivation of diagnostic device components, microtiter plates, or fluidic paths to reduce nonspecific adsorption during analytical workflows.
PEG–silane layers on silica or glass can improve reproducibility in chromatographic or microarray processes by minimizing sample loss to surfaces.
As a component in research-scale surface treatments for containers and sensors used in development labs. Not for clinical or therapeutic use.
Physical Properties
Item-specific values
Appearance: Not specified for this item; refer to CoA/Spec Sheet.
Grade/Purity: Not specified for this item; refer to CoA/Spec Sheet.
Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.
Other specifications (bp/mp, density, refractive index, water/peroxide/metal limits, UV cutoff): Not specified for this item; refer to CoA/Spec Sheet.
General/literature characteristics for PEG–trialkoxysilanes (non-specific guidance)
Physical state: typically clear to pale viscous liquids or low-melting waxy solids depending on PEG length; PEG5–TES commonly a low-viscosity to moderately viscous liquid.
Solubility: good solubility in polar aprotic organic solvents (DCM, THF, acetone, acetonitrile) and alcohols; miscibility with water is limited and leads to hydrolysis of –Si(OEt)3 under acidic/basic conditions.
Volatility: low; trialkoxysilanes slowly hydrolyze in humid air releasing ethanol.
Polarity: amphiphilic; PEG segment is highly hydrophilic (strong hydrogen-bond acceptor), silane end is hydrolyzable.
Stability: moisture sensitive; hydrolyzes to silanols and ethanol which can further condense to siloxanes (crosslinking/gelation risk in humid conditions).
Practical notes (general)
Handle under dry, inert atmosphere to preserve alkoxy functionality.
Use dry solvents; exclude water during solution preparation unless performing controlled aqueous silanization.
Quality and Grades
Item-specific grade/purity: Not specified for this item; refer to CoA/Spec Sheet.
General guidance for evaluating PEG–silane quality (literature/practice)
Purity dimensions: organic purity (NMR/LC), hydrolyzable alkoxy content (titration or 29Si NMR), residual solvents, water content (Karl Fischer), and siloxane dimer/polymer levels. For surface chemistry, low pre-condensed siloxane is critical for forming uniform monolayers.
End-group fidelity: verify methoxy capping and exact PEG length distribution (PEGs are often polydisperse; narrow dispersity improves reproducibility in surface passivation).
Trace metal/ionic content: low ionic contamination helps avoid catalytic hydrolysis and preserves substrate properties; when relevant, request ICP and ion chromatography data.
Stabilizers: Some trialkoxysilanes are shipped with trace acidic inhibitors or aseptic filtration. If stabilizers are present, they can influence silanization pH and kinetics. Not specified for this item; refer to CoA/Spec Sheet.
Optical cleanliness: For photonics/microfluidics, low UV–Vis absorbance of residues is important—choose high-purity, low-residue grades when patterning or bonding optics.
Documentation
Request CoA with water content and assay at time of shipment; small deviations can significantly impact silanization performance.
Silanization/coupling agent to graft a protein-resistant, hydrophilic mPEG5 layer onto hydroxylated substrates (glass, silica, quartz, alumina, TiO2). The methoxy terminus provides an inert, non-fouling surface.
Typical use cases
Anti-fouling coatings on microfluidic channels and biosensor chips to reduce nonspecific adsorption of proteins and cells.
Stabilization and steric protection of oxide-surface nanoparticles (e.g., silica, TiO2) to minimize aggregation in aqueous media.
Surface energy tuning for soft lithography, microcontact printing backfills, and reduction of biofouling in diagnostic devices.
Passivation layers preceding site-specific functionalization by co-deposition with functional silanes (e.g., aminosilanes) to control ligand density.
Mechanistic notes (general)
Step 1: Hydrolysis of –Si(OEt)3 to –Si(OH)3 (catalyzed by acid/base, moisture) with ethanol release.
Step 2: Condensation of silanols with surface –M–OH (M = Si, Al, Ti) forming –M–O–Si– linkages, followed by lateral siloxane crosslinking.
The PEG chain remains intact; methoxy end group is non-reactive under silanization conditions.
Practical tips
Clean/activate surfaces (piranha, oxygen plasma, or base/acid wash) to increase –OH density; rinse and dry thoroughly.
Use 0.2–3% v/v silane in anhydrous solvent for solution-phase or vapor deposition; incubate 30–120 minutes depending on method (literature guidance).
Post-deposition cure at 100–120°C for 10–60 minutes to strengthen siloxane bonds and remove residual ethanol/solvent.
Minimize water during non-aqueous processes to avoid bulk gelation and particle formation.
Reaction Conditions
General literature guidance for silanization with mPEG–trialkoxysilanes (optimize per substrate and setup; values are not item-specific specifications):
Substrate preparation
Clean glass/silica by piranha (H2SO4/H2O2; handle with extreme caution) or base-peroxide (NH4OH/H2O2/H2O) or oxygen plasma. Rinse thoroughly and dry at 110–150°C to dehydrate surface.
Non-aqueous silanization (solution-phase)
Solvent: anhydrous toluene, heptane, THF, or DCM.
Concentration: 0.2–2% v/v silane.
Temperature/time: 20–80°C for 0.5–2 h; gentle agitation.
Post-treatment: rinse with dry solvent, then cure 100–120°C for 30–60 min.
Vapor-phase deposition
Place cleaned substrates with a reservoir of silane in a dry chamber; 50–90°C for 1–3 h under reduced pressure or inert sweep. Follow by thermal cure.
Aqueous alcohol method (pre-hydrolysis)
Vehicle: ethanol/water (95:5 to 70:30 v/v) adjusted to pH 4.5–5.5 (acetic acid).
Pre-hydrolysis: 5–30 min at room temperature, then immerse substrates 10–60 min.
Rinse sequence: ethanol → water → ethanol; dry and cure 100–120°C.
Expected outcomes (literature)
Formation of sub-nanometer to few-nanometer PEG layers; contact angle reduction and significant suppression of protein adsorption relative to bare surfaces.
Cautions
Avoid high silane concentrations that promote multilayering and hazy films.
Exclude dust/particulates; filter solutions (0.2 µm, dry) to improve film quality.
Safety and Handling
Item-specific hazard data
GHS Classification, Signal word, H-statements, Pictograms: Not specified for this item; refer to SDS.
General safety considerations for trialkoxysilanes and PEG–silanes (not product-specific; consult SDS for authoritative data)
Hazards: moisture-sensitive; hydrolysis liberates ethanol (flammable) and forms silanols that can condense exothermically on surfaces. Liquid may cause eye/skin irritation. Vapors are usually low but avoid inhalation of aerosols.
Incompatibilities: moisture, strong acids/bases (accelerate hydrolysis/condensation), strong oxidizers. Avoid contact with reactive metals where ethanol generation could be problematic.
Personal protective equipment: lab coat, safety glasses or face shield, and appropriate chemical-resistant gloves (e.g., nitrile). Work in a fume hood when preparing solutions or performing silanization.
Handling: open only under dry conditions; purge headspace with nitrogen/argon after use. Wipe bottle threads and reseal promptly. Avoid contamination with water, acids, or bases unless conducting controlled hydrolysis.
First aid (general): in case of skin contact, wash with plenty of water/soap; eye contact, rinse cautiously with water for several minutes and seek medical attention; inhalation, move to fresh air; ingestion, rinse mouth—seek medical advice. Refer to SDS for full instructions.
Spill/Disposal: absorb with inert material; prevent entry into drains. Dispose according to institutional and local regulations. Note potential for polymeric siloxane formation on neutralization.
Solvent Selection
Solvent compatibility (general for PEG–trialkoxysilanes)
Preferred anhydrous solvents for non-aqueous silanization: toluene, heptane, cyclohexane, dry THF, dry DCM. These limit premature hydrolysis and allow vapor- or solution-phase deposition.
For controlled hydrolytic deposition: ethanol/water or isopropanol/water mixtures adjusted to pH ~4.5–5.5 (acetic acid) can be used to pre-hydrolyze –Si(OEt)3 to silanols before surface condensation.
Solubility: excellent in polar aprotic solvents; miscible with alcohols; limited in alkanes as PEG length increases but typically workable at low wt%.
Polarity and dielectric (literature trends)
PEG chain raises polarity and hydrogen-bond acceptor capacity; dielectric constant of solutions will be dominated by the solvent chosen (e.g., THF ~7.6, toluene ~2.4 at 20°C; literature values).
Selection guidance
Choose dry, non-protic solvents when targeting self-assembled monolayers with minimal polymerization.
Choose aqueous alcohol (acidic) when targeting robust siloxane networks or rapid priming of glass/silica.
Avoid ketones/alcohols if uncontrolled hydrolysis/condensation would foul equipment.
Ethanol/water (pH ~5): faster hydrolysis; good for uniform coverage after proper rinsing/cure.
THF/DCM: good solvating power; ensure dryness to suppress premature gelation.
Storage and Reconstitution
Item-specific conditions (from Product Data)
Storage: Store at -20°C.
Shipping: Shipped in ice chest with ice pads.
General guidance for this class of reagents
Moisture protection: store under inert gas in tightly sealed, moisture-barrier containers (e.g., amber glass with PTFE-lined cap) inside a desiccated secondary container.
Temperature: low temperature slows hydrolysis and self-condensation; allow container to equilibrate to room temperature before opening to avoid moisture condensation.
Handling after opening: minimize headspace; backfill with dry nitrogen/argon; promptly reseal. Consider aliquoting under dry conditions to limit repeated exposure.
Solution stability: prepare working solutions in dry solvents immediately before use. Avoid storing aqueous or alcoholic solutions—hydrolysis proceeds even at mild acidity.
Appearance changes: increased viscosity, haze, or gel formation can indicate partial hydrolysis/condensation; discard if film quality is compromised.
Thawing/use: if material is highly viscous at low temperature, warm gently to room temperature before dispensing; do not heat while sealed if condensation is possible.
Documentation
For exact shelf life and any stabilizers present: Not specified for this item; refer to CoA/Spec Sheet.
Structure and Identity
Brief overview: m-PEG5-triethoxysilane is a methoxy-terminated polyethylene glycol (five ethylene oxide repeat units) bearing a trialkoxysilane anchoring group for covalent attachment to hydroxylated inorganic surfaces (e.g., glass, silica, metal oxides).
Item-specific (from Product Data)
Product name: m-PEG5-triethoxysilane
CAS: 2243566-42-7
SMILES: Not specified for this item; refer to CoA/Spec Sheet.
InChIKey: Not specified for this item; refer to CoA/Spec Sheet.
Molecular formula: Not specified for this item; refer to CoA/Spec Sheet.
Molecular weight: Not specified for this item; refer to CoA/Spec Sheet.
Structural features (general/literature description)
Functional groups: terminal methoxy (–O–CH3) cap; PEG chain with ~5 ethylene oxide units [–(CH2–CH2–O)5–]; triethoxysilane moiety [–Si(OEt)3].
Connectivity: mPEG chain linked to silicon via –O–Si(OC2H5)3; the opposite terminus is methoxy-capped (non-reactive, hydrophilic tail).
2D structure (verbal): a linear polyether chain terminated on one end by a methoxy group and on the other by a tetrahedral silicon bearing three ethoxy substituents; no rings, no stereocenters.
Intended function: trialkoxysilane undergoes hydrolysis/condensation to form surface Si–O–Si bonds; the PEG5 segment imparts hydrophilicity and protein-resistance.
Synonym notes (general)
Also described as MeO–PEG5–Si(OEt)3, methoxy-PEG(5) triethoxysilane, or mPEG5–TES.
Synthetic Utility
Role in synthesis (general)
Acts as a bifunctional surface modifier: the trialkoxysilane end covalently anchors to hydroxylated inorganic substrates, while the methoxy-terminated PEG5 tail modulates interfacial properties (hydrophilicity, protein resistance).
Retrosynthetic/value considerations
Enables introduction of PEG spacers onto solid supports without additional reactive handles at the distal end—useful when an inert, blocking, or spacing layer is desired.
Can be co-deposited with functional silanes (e.g., amine-, azide-, or epoxy-silanes) to dilute reactive site density and control ligand spacing on biosurfaces.
Hydrolysis/condensation to form Si–O–Si linkages on silica, glass, Al2O3, TiO2, and some metal oxides.
Thermal curing to densify siloxane networks.
Vapor-phase deposition for high-uniformity coatings inside microfluidic channels.
Limitations
Not suitable for non-oxide substrates without prior surface oxidation/priming.
Over-hydrolysis leads to bulk siloxane gelation; careful solvent and water control are essential.
Target Specificity
Not applicable. This product is a chemical surface modifier, not a biological targeting reagent. No antigen/epitope or species reactivity is associated.
Häufig gestellte Fragen
What is the purity of this product?
This product is supplied at ≥98% purity (chemical assay). Lot-specific values are stated on the Certificate of Analysis.
How should this product be stored?
Store at ?20 °C. Freezer storage is required to maintain the specified shelf life.
How is this product shipped?
This product ships in an insulated container with ice pads. Unpack on arrival and transfer it to the storage condition stated above.
What are the CAS number, molecular formula and molecular weight?
The CAS Number is 2243566-42-7, the molecular formula is C21H45NO9Si, and the molecular weight is 483.7 g/mol.
What documentation is provided?
Available product documentation, including Certificates of Analysis (COA), Safety Data Sheets (SDS), and specification sheets, is shown in the product document area. Document availability and access follow the current site policy.
Wir verwenden Cookies, um die ordnungsgemäße Funktion der Website sicherzustellen und, soweit zulässig, Ihr Nutzererlebnis zu verbessern. Sie können Ihre Einstellungen jederzeit unter „Einstellungen“ verwalten. Weitere Informationen finden Sie in unserer Cookie-Richtlinie.
Dürfen wir Sie über Rabattaktionen informieren?
Später erinnern
Vielen Dank! Bitte überprüfen Sie Ihren E-Mail-Posteingang, um zu bestätigen.
Products are supplied to verified businesses, institutions, and qualified professionals for research and development use only. Not for use in humans, animals, diagnosis, or therapy.