Determine the necessary mass, volume, or concentration for preparing a solution.
For enumeration of molds and yeasts; add 220 g of glycerol per liter of medium
Item-specific validated protocols are not provided. General, literature-style workflow for enumeration on DG-type media:
Modified DG-18 Agar Base does not have a single biological role as a molecule; instead, as a complex medium it establishes environmental conditions that select for xerophilic and osmotolerant fungi. • Functional roles in culture (literature, general for DG-type media):
Not applicable. Modified DG-18 Agar Base is a complete culture medium base rather than a buffering reagent. While prepared media possess a defined pH, the product is not used to formulate laboratory buffer systems. For practical guidance, see Storage & Reconstitution and Reaction & Applications.
Green chemistry considerations are limited for dehydrated culture media, which are water-based and used at modest concentrations. • Potential improvements (general):
Direct pharmaceutical formulation/excipient uses are not typical. In pharma/biotech quality control laboratories, DG-type agars may be used in non-clinical environmental or raw-material monitoring to assess fungal bioburden in dry/high-sugar matrices (lab QC context). No therapeutic or clinical diagnostic use is intended or implied. Compendial status (e.g., pharmacopeial monographs) is not specified for this item; refer to CoA/Spec Sheet and your quality system for suitability assessments.
Item-specific physico-chemical constants are not provided for this complex mixture.
• Form: Dehydrated blend/powder (general for agar media; item-specific appearance not provided). • Solubility: Dispersible in water upon heating; forms a gel on cooling due to agar content (general, literature). • pH (prepared medium): Not specified for this item; refer to CoA/Spec Sheet. (DG-18 media are commonly near neutral–slightly acidic in literature.) • Moisture sensitivity: Dehydrated media are typically hygroscopic; keep container tightly closed to prevent clumping and performance drift (general guidance). • BP/MP, density, refractive index, logP, pKa: Not applicable/Not specified for this heterogeneous medium; refer to CoA/Spec Sheet for any lot-specific details. • Color/clarity (prepared plates): Typically light amber and slightly opalescent after sterilization and pouring (literature, general for DG-type media), but appearance can vary with water quality, autoclave cycle, and supplements. • Sterility: Prepared medium must be sterile; verify via sterility control plate (general best practice).
• Grade: BioReagent (item-specific). This denotes suitability for laboratory research applications where consistent biological performance is required. BioReagent-grade media components are produced and packaged to minimize lot-to-lot variability and bioburden. • Performance attributes (general for microbiological media):
This product is not used as a reagent in synthetic organic reactions. Its primary application is microbiological culture of xerophilic and osmotolerant fungi on low–water-activity agar (general for DG‑type media). Practical laboratory applications (literature/guideline-based): • Food microbiology: Enumeration of yeasts and molds in high-sugar or low‑aw foods (dried fruits, confectionery, spices), where reduced aw and dichloran minimize overgrowth and facilitate colony counting. • Environmental monitoring: Recovery of xerotolerant fungi from dry processing environments. • Method frameworks: Commonly referenced in ISO/ICUMSA/US FDA BAM style protocols for fungal counts in foods (literature), often with specified incubation temperatures (e.g., 25–30 °C) and durations (3–7 days), and optional antibiotics to suppress bacteria. • Practical tips:
Not applicable to chemical reactions. For microbiological use, typical incubation conditions on DG-type media (literature, general guidance) include: • Temperature: Commonly 25–30 °C depending on method and target organisms. • Atmosphere: Aerobic incubation; plates inverted to reduce condensation. • Duration: Often 3–7 days, extending to 10 days for slow growers; enumerate at specified intervals. • Selective supplements: Some protocols add antibiotics (e.g., chloramphenicol) to further suppress bacteria—follow validated procedures. Refer to your method (ISO/industry standard or internal SOP) for exact parameters. Item-specific preparation conditions are provided on the label/CoA.
• GHS/CLP: Not specified for this item; refer to the product SDS for authoritative hazard classification, pictograms, signal word, and H‑statements. • Likely hazards (general for dehydrated media): Dust may cause mechanical irritation to eyes, skin, or respiratory tract; some blends may contain inhibitors (e.g., dichloran) that warrant enhanced care. Avoid inhalation of dust and contact with eyes/skin. Do not ingest. • PPE (best practice): Laboratory coat, nitrile gloves, safety glasses/goggles, and dust control (work in a fume hood or use local exhaust) when handling powders. Use heat-resistant gloves when removing hot media from autoclave/water bath. • Handling: Minimize dust generation. Weigh promptly; re-seal container immediately. Prepare media with appropriate sterilization (typically autoclaving). Prevent post-sterilization contamination. • Incompatibilities (general): Strong oxidizers/reactives are not typically encountered in media prep; however, avoid contact with strong oxidants and acids/bases that could degrade nutrients. Do not autoclave in sealed containers; ensure steam can vent. • Thermal hazards: Autoclaving at 121 °C under pressure poses burn/scald risks. Allow vessels to depressurize fully before opening. • Spill response: Avoid creating dust; sweep or vacuum with HEPA filtration. Wash area with water. • First aid (overview; refer to SDS): Eye contact—rinse with water for several minutes; remove contacts if easy. Skin—wash with soap/water. Inhalation—move to fresh air. Ingestion—rinse mouth; seek medical advice if symptoms persist. • Waste: Dispose of unused dehydrated powder and prepared culture plates according to institutional biohazard and chemical waste policies. Decontaminate used plates by autoclaving before disposal.
Not typically applicable. Modified DG-18 Agar Base is intended to be dispersed in purified water to prepare a solid culture medium. Selection considerations are limited to water quality (e.g., ASTM Type II or better) and optional supplements per method requirements. For other uses, see Reaction & Applications and Storage & Reconstitution.
• Storage (item-specific): Store at room temperature. Keep container tightly closed. Protect from moisture. • Shipping: Shipped in normal conditions (item-specific). • Shelf life: Not specified for this item; refer to CoA/Spec Sheet. • Reconstitution/Preparation (general media guidance; not item-specific):
• Item type: Modified DG-18 Agar Base is a dehydrated, multi‑component microbiological culture medium base formulated for the isolation/enumeration of xerophilic and osmotolerant fungi from foods and environmental samples. • Composition nature: Complex mixture (peptones/yeast extracts, carbohydrates/osmotic modifiers, selective agents such as dichloran, and agar). Exact formulation varies by manufacturer. • Molecular formula: Not specified for this item; refer to CoA/Spec Sheet. • Molecular weight: Not specified for this item; refer to CoA/Spec Sheet. • SMILES / InChI / InChIKey: Not applicable to complex mixtures; not specified for this item; refer to CoA/Spec Sheet. • Structural description (general): Heterogeneous solid blend; no single defined 2D structure. Functional classes (literature, typical):
Not applicable to synthetic chemistry. Modified DG-18 Agar Base is not a reagent for chemical transformations. Its value lies in microbiological selectivity and plate-based enumeration of xerophilic fungi. For usage details, see Reaction & Applications and Application Protocols.
Not applicable. This product is not an antibody, probe, or affinity reagent. It is a culture medium base with functional selectivity for xerophilic/osmotolerant fungi (general microbiological selectivity rather than molecular target specificity). See Biological Roles.
Unser Leitfaden zur Qualitätsauswahl behandelt Reinheit, Stabilisatorstatus und Anwendungseignung für alle Varianten in unserem Katalog.
BioReagent Qualitätsleitfaden ansehen →