Determine the necessary mass, volume, or concentration for preparing a solution.
Dilution Calculator
Determine the dilution needed to prepare a stock solution.
Reconstitution Calculator
Bewertungen
Kundenbewertungen
Application Protocols
Item-specific, validated application protocols are Not specified for this item; refer to CoA/Spec Sheet. The following general procedures are provided for research planning.
A. Preparation of a working dispersion (general)
Gently invert the container to homogenize. If sediment is present, bath-sonicate 10–30 min; avoid overheating. Optionally probe-sonicate at low duty cycle while cooling. Centrifuge (e.g., 5,000–10,000 g, 10–30 min) and collect the supernatant for well-dispersed fraction.
B. Vacuum-filtration TCF fabrication (aqueous surfactant system)
Filter a measured volume through a 0.1–0.2 µm membrane (MCE or PTFE). Rinse with water/alcohol to remove surfactant. Transfer film to substrate by dissolving the membrane (e.g., acetone for MCE) or by hot-press lamination. Dry and anneal (150–250°C, substrate-limited). Measure sheet resistance and transmittance.
C. Spin coating or spray coating (organic system)
Adjust concentration/viscosity to target thickness. For spin coating, 500–2,000 rpm, 30–60 s; bake to remove solvent. For spray, maintain warm substrate and controlled flow to avoid coffee-ring effects. Post-treat (acid/base dopants) as required.
D. Composite preparation
Mix SWCNT dispersion with polymer solution or latex under shear; consider compatibilizers or covalent functionalization for interfacial adhesion. Remove solvent under reduced pressure; cure per resin specifications.
Quality controls
Track concentration (gravimetry or UV–Vis–NIR), evaluate dispersion by Raman and optical density, and document any post-treatments to ensure reproducibility.
Biological Roles
This product is a nanocarbon material for research and materials science. Item-specific biological data are Not specified for this item; refer to CoA/Spec Sheet. No medical or clinical claims are made.
General/literature context on SWCNT–biology interactions (for researchers):
SWCNTs have no native biological role; however, noncovalent adsorption (e.g., with DNA, proteins, or phospholipids) enables dispersions in aqueous buffers and has been explored for biosensing and delivery in research settings.
Optical properties: Certain semiconducting chiralities exhibit NIR photoluminescence (E11 transitions) that can be modulated by local environment, forming the basis of analyte-responsive nanosensors (e.g., for small molecules, reactive species) in model systems.
Protein corona formation: In biological fluids, surfactant-stripped or functionalized SWCNTs acquire protein coronas that alter dispersion stability and cellular interactions (literature observation).
Cytocompatibility/toxicity depend on length, purity (metal residues), surface chemistry, and dose. Oxidative debris and catalyst residues can drive responses; rigorous purification and characterization are essential for in vitro studies.
Enzymatic and oxidative degradation of functionalized CNTs has been reported under certain conditions (e.g., peroxidase-mediated), but rates are strongly dependent on defect density and functional groups.
Practical notes:
If using in bioassays, select biocompatible dispersants (e.g., DNA, Pluronic) and remove cytotoxic surfactants (e.g., SDBS) thoroughly. Validate endotoxin and metal content where relevant to the study design.
Maintain compliance with institutional biosafety and nanomaterial handling policies; dispose of CNT-containing biological waste via approved routes.
Buffer Applications
SWCNT dispersions are not buffers and are not typically used to establish or maintain pH. Therefore, classic buffer formulation (pKa selection, buffering range) does not apply.
Relevant guidance for working with SWCNTs in buffered media (general):
If dispersing SWCNTs in aqueous buffers for research, select ionic strengths and additives that support dispersion stability (e.g., maintain sufficient surfactant concentration above its CMC for SDS/SDBS systems). High salt can screen electrostatic stabilization and promote rebundling.
Avoid multivalent cations (e.g., Ca2+, Mg2+, Al3+) in surfactant-stabilized dispersions unless their effects are characterized; they can precipitate anionic surfactants and flocculate CNTs.
For biological assays, use biocompatible dispersants (DNA, bile salts, Pluronics) and pre-clear by centrifugation to remove aggregates. Filter selection should consider nanotube length (e.g., 0.2–0.45 µm membranes may retain bundles).
pH sensitivity: Covalently functionalized SWCNTs bearing carboxyl or amine groups show pH-dependent colloidal stability; characterize zeta potential in your chosen buffer.
Item-specific buffer suitability or recipes are Not specified for this item; refer to CoA/Spec Sheet.
Green Alternatives
Item-specific solvent system is Not specified for this item; refer to CoA/Spec Sheet.
Greener dispersion strategies for SWCNT processing (literature-based comparison):
Water + bio/safe surfactants
Pros: Low toxicity, minimal VOCs; facile cleanup; compatible with roll-to-roll coating.
Cons: Surfactant removal needed to achieve high conductivity; rinses may alter film morphology.
Pros: Improved EHS profiles versus NMP/DMF; good solvency parameters for graphitic carbons when combined with additives.
Cons: Drying behavior and viscosity differ; may need co-solvents or dispersants to reach target concentration.
Polymer-assisted dispersion in green media (e.g., cellulose derivatives, PVA)
Pros: Process aids become part of the final matrix (composites, inks), reducing wash steps.
Cons: Potentially lower conductivity vs surfactant-free, requires optimization of polymer content.
Avoided chemistries
Superacids (chlorosulfonic acid) dissolve SWCNTs but are corrosive and hazardous; generally replaced by safer dispersion approaches unless true molecular dispersion is required.
Selection guidance:
For TCFs and sensors on flexible substrates, start with aqueous surfactant dispersions; use mild acid/alcohol rinses followed by low-temperature anneals to reduce residue.
When replacing NMP, evaluate Cyrene or propylene carbonate with calibrated sonication and small amounts of amphiphiles (e.g., pyrene-derivatized surfactants) to approach NMP-like debundling.
Conduct a full EHS review including worker exposure, VOC content, and waste treatment when modifying ink vehicles.
Pharmaceutical Uses
This product is supplied for research use only. No medical or clinical uses are claimed or supported. Item-specific regulatory status (e.g., pharmacopeial listing), excipient qualification, or GMP status are Not specified for this item; refer to CoA/Spec Sheet.
General context (literature/industry):
SWCNTs are investigated in research settings for roles such as conductive additives in device fabrication, biosensing transducers, and as components of diagnostic platforms. These are preclinical/analytical utilities rather than approved pharmaceutical applications.
As an excipient or processing aid, CNTs are not recognized by major pharmacopeias for drug product use. Manufacturing environments typically avoid airborne nanocarbons due to EHS considerations.
For analytical and device-related support of pharmaceutical R&D, SWCNT films and inks can serve as conductive tracks or sensor elements in lab-on-chip devices, electrochemical sensors, and flexible circuits used in research instrumentation.
Practical notes for regulated environments:
If using in a GMP-adjacent laboratory (e.g., device prototyping), implement robust supplier qualification and material specifications (metal residue limits, particulates, bioburden, endotoxin if relevant) and maintain full traceability.
Ensure segregation between nanomaterial handling areas and pharmaceutical manufacturing spaces; follow institutional nanomaterial hygiene, waste, and exposure monitoring policies.
Physical Properties
Item-specific physicochemical specifications (concentration, solvent composition, appearance, density, viscosity, UV cutoff, solids content) are Not specified for this item; refer to CoA/Spec Sheet.
General/literature properties of SWCNTs and their dispersions (for context only):
Solid SWCNT intrinsic density: ~1.3–1.4 g/cm³ (literature; depends on packing/bundling). Apparent bulk densities are much lower due to porosity.
Solubility: Pristine SWCNTs are insoluble in most solvents; they can be dispersed (not dissolved) by noncovalent stabilization. Effective media include water with anionic surfactants (e.g., SDS, SDBS), bile salts, DNA, or high-boiling polar aprotic solvents such as NMP, DMF, DMAc (literature). Covalent functionalization (e.g., –CO2H, –Ar) can improve dispersibility in polar solvents.
Optical features: UV–Vis–NIR spectra show E11/E22 transitions for semiconducting tubes and M11 for metallic tubes; the relative band structure is chirality-dependent (literature). Raman shows strong G-band (~1590 cm⁻¹), radial breathing modes (RBMs) whose frequencies correlate with tube diameter, and D-band (~1350 cm⁻¹) as a defect indicator.
Electrical/thermal: Intrinsically high electrical conductivity (especially for metallic tubes) and exceptional thermal conductivity along the tube axis (literature). In dispersions, measured properties are dominated by concentration, bundling state, and stabilizer.
Practical notes:
Viscosity and density of a dispersion are dominated by the continuous phase (solvent/surfactant) and nanotube loading; consult the CoA for item-specific values.
If concentration is required for process design, determine by gravimetry or UV–Vis–NIR using an appropriate extinction coefficient for the specific medium (literature method).
Quality and Grades
Item-specific grade/purity, stabilizer, solvent system, concentration, and analytic metrics are Not specified for this item; refer to CoA/Spec Sheet.
How to evaluate SWCNT dispersion quality (general guidance for professional users):
Structural distributions: Diameter and chirality (n,m) affect optical and electronic properties. Quality datasets typically include UV–Vis–NIR spectra (E11/E22 features) and resonant Raman RBMs to evidence debundled SWCNTs and diameter distributions.
Defect level: Raman D/G or ID/IG ratio indicates sidewall defect density; lower ID/IG implies more pristine tubes. After oxidation or covalent functionalization, D-band increases.
Metal catalyst residues: ICP-OES/ICP-MS for Fe, Co, Ni, Mo, Y, etc. Reported as ppm or wt%. Lower residuals are preferred for electronic/opto applications.
Dispersity: Dynamic light scattering (DLS, used cautiously), analytical ultracentrifugation, or UV–Vis-derived metrics can indicate debundling. Sedimentation tests (centrifugation at defined g) give practical stability readouts.
Concentration: Verified by gravimetry (filter, dry, weigh) or extinction coefficients specific to the solvent/surfactant system.
Stabilizer identity: For aqueous systems, common surfactants include SDS, SDBS, DOC/SDC, Triton X-100; for organic media, NMP, DMF, DMAc. Knowledge of stabilizer informs downstream compatibility (e.g., film conductivity post-rinse).
Particle cleanliness: TOC and residual surfactant content matter for electronics; XPS/FTIR can detect adventitious oxygen or functional groups.
Implications for use:
High-purity, debundled, surfactant-defined dispersions enable reproducible transparent conductive films and spectroscopy. For composites, broader length distributions may aid percolation but complicate rheology.
Reaction and Applications
This product is intended for materials science and nanotechnology applications. Item-specific application validations are Not specified for this item; refer to CoA/Spec Sheet.
Representative application areas for SWCNT dispersions (literature/practice):
Transparent conductive films (TCFs): Fabrication by vacuum filtration/transfer, spray or spin coating. Post-treatments (acid doping, surfactant removal) reduce sheet resistance while maintaining high transmittance.
Printed/flexible electronics: Inks for inkjet, aerosol jet, and screen printing to create interconnects, strain gauges, touch sensors, and antennas.
Energy storage: Conductive additives in Li-ion/S batteries and supercapacitors; SWCNT networks improve rate capability and mechanical integrity.
Composites: Reinforcement of thermoplastics/thermosets; percolated networks offer electrical conductivity at low loadings and enhanced toughness.
Sensors: Chemiresistors and strain/pressure sensors utilizing the piezoresistive response of percolated SWCNT networks; functionalization tailors selectivity.
Photonics/optics: Saturable absorbers (NIR), photothermal materials, and EMI shielding coatings.
Covalent: Sidewall functionalization via diazonium chemistry, nitrene additions (from azides), fluorination/defluorination, and cycloadditions (e.g., Prato). Oxidative cutting/end-group carboxylation with nitric/sulfuric acid mixtures introduces –CO2H for further coupling.
Practical tips:
Control bundling via calibrated sonication and centrifugation. Excess sonication shortens tubes and raises defect density (higher Raman D/G).
For devices, filter through mixed-cellulose ester or PTFE membranes and transfer; optimize annealing (150–300°C, substrate-limited) to remove residues.
Reaction Conditions
Item-specific reaction conditions are Not specified for this item; refer to CoA/Spec Sheet. The following are literature/general conditions for common SWCNT functionalizations. Always perform thorough risk assessments and consult primary literature.
Oxidative cutting/carboxylation: Reflux or controlled sonication in mixed acids (e.g., HNO3/H2SO4, varied ratios) at 0–80°C for 1–6 h. Purpose: shorten tubes, open ends, introduce –CO2H. Notes: vigorous gas evolution and heat; neutralize carefully; extensive washing/dialysis required.
Aryl diazonium functionalization: Generate diazonium in situ from anilines/NaNO2/HCl at 0–5°C; react with SWCNT dispersion (aqueous surfactant or organic) at 0–25°C for 0.5–4 h. Quench with base or sulfite; monitor D/G ratio and UV–Vis.
Nitrene addition (from azides): Thermal activation in high-boiling solvents (e.g., o-dichlorobenzene) or photolysis; temperatures 120–180°C for 1–12 h. Install aryl/amide groups; ensure adequate ventilation.
Fluorination/defluorination: XeF2 (solid–vapor) at room temperature to mildly elevated temperatures in inert atmosphere; subsequent nucleophilic substitution (amines, alkoxides) in polar aprotics at 25–100°C.
Prato cycloaddition: Generate azomethine ylide from an aldehyde + amino acid (e.g., sarcosine) in refluxing toluene or o-dichlorobenzene (110–180°C) for 6–24 h; yields pyrrolidine rings on sidewalls.
Noncovalent functionalization: Sonicate with π-stacking agents (pyrene derivatives) or surfactants in water/organics; control power and duty cycle to limit shortening; centrifuge to remove aggregates.
Characterization checkpoints: Raman (D/G, RBMs), UV–Vis–NIR (E11/E22), TGA (functional group loading), XPS (heteroatom content), TEM/AFM (length/dispersion state), and ICP for metal residues.
Safety and Handling
Hazard classification
GHS classification, signal word, pictograms, and H-statements: Not specified for this item; refer to SDS.
General safety guidance for CNT dispersions (literature/practice; not item-specific):
Personal protective equipment: Lab coat, safety glasses, and chemically resistant gloves. Use a fume hood to limit aerosol formation when sonicating or spraying.
Avoid generating mists or aerosols. While dispersions reduce inhalation risk compared to dry powders, secondary aerosolization can occur during sonication, spraying, or high-shear mixing.
Incompatibilities: Strong oxidizers may aggressively oxidize nanotube sidewalls; concentrated mineral acids/bases can alter functionalization and release heat. Avoid mixing with halogenating agents unless intentional functionalization is planned.
Peroxide formation: Not applicable to carbon nanotubes; however, certain organic dispersion media (e.g., ethers) can form peroxides—follow solvent SDS.
First aid (overview; defer to SDS):
Inhalation of mist: Move to fresh air; seek medical attention if symptoms persist.
Skin contact: Wash with soap and water; remove contaminated clothing.
Eye contact: Rinse cautiously with water for several minutes; remove contact lenses if present and easy to do; seek medical attention if irritation persists.
Ingestion: Rinse mouth; do not induce vomiting; seek medical advice.
Handling tips: Seal containers promptly to limit evaporation and concentration drift. During sonication, use sealed tubes and secondary containment; allow degassing time before opening. Centrifuge or allow sediments to settle before decanting supernatant to minimize exposure to agglomerates.
Waste: Collect CNT-containing waste as nanomaterial/chemical waste per institutional policy; do not discharge to drains.
Solvent Selection
Item-specific solvent composition is Not specified for this item; refer to CoA/Spec Sheet.
General solvent/dispersant strategies for SWCNTs:
Aqueous systems: Use anionic surfactants (SDS, SDBS), bile salts (DOC/SDC), DNA, or polymers (PVP) with bath or probe sonication to debundle. Advantages: greener medium, facile processing, easy cleanup. Considerations: residual surfactant may reduce film conductivity; post-treatments (methanol rinse, acid dopants) often required.
Polar aprotic solvents: NMP, DMF, DMAc, DMSO can disperse SWCNTs without surfactants due to favorable Hansen parameters; useful for high-solid inks and spin coating. Tradeoffs: toxicity/regulatory profile (e.g., NMP), high boiling points complicate drying.
Other media: Ionic liquids, superacids (e.g., chlorosulfonic acid for true solutions; highly corrosive), and bio-derived solvents (e.g., Cyrene) are explored for specialized processing.
Selection guidance (literature-based):
Transparent conductive films: Start with aqueous SDBS or DOC dispersions; vacuum filtration/transfer yields low-haze films. Post-rinse and acid doping improve sheet resistance.
Printed electronics: NMP or DMF dispersions give smoother films via inkjet/aerosol jet; ensure substrate compatibility and controlled drying.
Composites: Choose a solvent compatible with the polymer matrix or pre-functionalize SWCNTs for better interfacial adhesion (e.g., –CO2H in epoxy systems).
Quick comparison (general):
Water + surfactant: green, easy handling; needs surfactant removal.
NMP/DMF: good dispersion without surfactant; health/safety and drying challenges.
Cyrene/propylene carbonate: improved EHS profile vs NMP; may require optimization of sonication and additives.
Appearance, solvent, concentration, stabilizers: Not specified for this item; refer to CoA/Spec Sheet.
General storage guidance for SWCNT dispersions:
Store in a tightly closed container to minimize solvent evaporation and concentration drift. If the medium is water/surfactant, room temperature storage is typically acceptable; avoid prolonged exposure to direct sunlight and freeze–thaw cycling, which can destabilize dispersions.
If stored for extended periods, inspect for sedimentation or phase separation. Redisperse by gentle inversion or bath sonication. Avoid vigorous shaking that can introduce bubbles/aerosols.
For organic solvent systems (e.g., NMP/DMF), ensure compatible caps/seals to prevent swelling and maintain an inert headspace if oxidation-sensitive additives are present.
Reconstitution/redispersion tips (general):
If the dispersion concentrates or partially dries, add the original solvent/medium (or a compatible diluent) in measured volume, then bath-sonicate while cooling until homogeneous. Filter (0.45–1.0 µm) if needed to remove large agglomerates.
For precise work, determine concentration post-redispersion by gravimetry or UV–Vis–NIR with an extinction coefficient appropriate to the dispersion medium.
Research use note: For research use only (from Product Data). Always consult the product’s CoA and SDS for item-specific guidance before use.
Structure and Identity
This product is a dispersion of single-wall carbon nanotubes (SWCNTs), a 1D allotrope of carbon consisting of a single graphene sheet seamlessly rolled into a hollow cylinder.
CAS: Not specified for this item; refer to CoA/Spec Sheet.
Molecular formula: Not applicable to a polydisperse nanocarbon; overall empirical composition is carbon (sp2). Item-specific value not specified.
Molecular weight: Not applicable (polydisperse length distribution). Item-specific value not specified.
SMILES / InChI / InChIKey: Not applicable for extended nanostructures.
Structural features (general/literature):
Constructed from sp2-hybridized carbon in a honeycomb lattice forming a cylinder with discrete chiral indices (n,m) that define diameter and electronic type (metallic or semiconducting).
Typical outer diameters for SWCNTs are ~0.7–2.0 nm; lengths range from tens of nm to many µm (literature, varies by source and processing).
Ends may be open or capped (hemifullerene-like). Sidewalls are typically pristine graphitic carbon but may carry defects or functional groups after processing.
Electronic structure: depending on (n,m), tubes exhibit 1D metallic or semiconducting behavior with van Hove singularities, observable by UV–Vis–NIR absorption and resonant Raman (literature).
2D description in words (general):
Imagine a single layer of graphene rolled into a cylinder; hexagonal carbon rings form the sidewall with no heteroatoms. The cylinder is hollow, high aspect ratio, and can bundle via π–π interactions. Dispersions often employ surfactants or high-boiling polar aprotic solvents to debundle tubes.
Synthetic Utility
Although not a molecular reagent, SWCNTs function as a versatile nanocarbon scaffold for chemical modification and materials synthesis.
Key reactive motifs (general/literature):
Graphitic sidewall (sp2 carbon): amenable to electrophilic additions (e.g., aryl diazonium coupling), radical additions, and cycloadditions (Prato 1,3-dipolar cycloaddition of azomethine ylides). These introduce functional groups while increasing defect density (monitored by Raman D/G).
Tube ends/defects: More reactive; oxidative unzipping/shortening in HNO3/H2SO4 generates carboxyls (–CO2H), which can be further converted (e.g., EDC/NHS coupling to amines, amidation, esterification) for polymer grafting or bioconjugation.
Heteroatom doping/halogenation: Fluorination (XeF2, F2) affords C–F functionalities; subsequent nucleophilic substitutions can install diverse groups. Nitrene additions from aryl azides incorporate arylamines/amide linkers.
Utility in synthesis and materials construction:
As a conductive nanoscale filler, SWCNTs establish percolation at low loadings in resins and elastomers, enabling antistatic and sensing composites.
As a templating scaffold, aligned or bundled SWCNTs guide inorganic deposition (e.g., metal nanoparticles, metal oxides) for catalysis and energy devices.
As a macromolecular building block, noncovalent functionalization with pyrene-terminated polymers or surfactants enables self-assembly and layer-by-layer films.
Practical considerations:
Balance functional group density against electronic/thermal performance; excessive covalent modification degrades conductivity.
Purification after reaction (filtration, centrifugation, dialysis) is essential to remove acids, salts, and small-molecule byproducts.
Item-specific functionality or pre-functionalization is Not specified for this item; refer to CoA/Spec Sheet.
Target Specificity
Not applicable. This product is a nanomaterial dispersion, not a biological affinity reagent. No antigen/epitope, clone, isotype, or species reactivity is relevant to this item. Item-specific targeting ligands, if any, are Not specified for this item; refer to CoA/Spec Sheet.
Wir verwenden Cookies, um die ordnungsgemäße Funktion der Website sicherzustellen und, soweit zulässig, Ihr Nutzererlebnis zu verbessern. Sie können Ihre Einstellungen jederzeit unter „Einstellungen“ verwalten. Weitere Informationen finden Sie in unserer Cookie-Richtlinie.
Dürfen wir Sie über Rabattaktionen informieren?
Später erinnern
Vielen Dank! Bitte überprüfen Sie Ihren E-Mail-Posteingang, um zu bestätigen.
Products are supplied to verified businesses, institutions, and qualified professionals for research and development use only. Not for use in humans, animals, diagnosis, or therapy.